/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright(c) 2007-2012 Intel Corporation. All rights reserved. */ /* * Copyright (c) 2008, 2010, Oracle and/or its affiliates. All rights reserved. */ /* IntelVersion: 1.146.2.2 v3_3_14_3_BHSW1 */ /* * 82575EB Gigabit Network Connection * 82575EB Gigabit Backplane Connection * 82575GB Gigabit Network Connection * 82576 Gigabit Network Connection * 82576 Quad Port Gigabit Mezzanine Adapter */ #include "igb_api.h" static s32 e1000_init_phy_params_82575(struct e1000_hw *hw); static s32 e1000_init_nvm_params_82575(struct e1000_hw *hw); static s32 e1000_init_mac_params_82575(struct e1000_hw *hw); static s32 e1000_acquire_phy_82575(struct e1000_hw *hw); static void e1000_release_phy_82575(struct e1000_hw *hw); static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw); static void e1000_release_nvm_82575(struct e1000_hw *hw); static s32 e1000_check_for_link_82575(struct e1000_hw *hw); static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw); static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, u16 *duplex); static s32 e1000_init_hw_82575(struct e1000_hw *hw); static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw); static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, u16 *data); static s32 e1000_reset_hw_82575(struct e1000_hw *hw); static s32 e1000_reset_hw_82580(struct e1000_hw *hw); static s32 e1000_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data); static s32 e1000_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data); static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active); static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw); static s32 e1000_setup_serdes_link_82575(struct e1000_hw *hw); static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data); static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, u16 data); static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw); static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask); static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed, u16 *duplex); static s32 e1000_get_phy_id_82575(struct e1000_hw *hw); static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask); static bool e1000_sgmii_active_82575(struct e1000_hw *hw); static s32 e1000_reset_init_script_82575(struct e1000_hw *hw); static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw); static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw); static void e1000_shutdown_serdes_link_82575(struct e1000_hw *hw); static s32 e1000_set_pcie_completion_timeout(struct e1000_hw *hw); static s32 e1000_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset); static s32 e1000_validate_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset); static s32 e1000_validate_nvm_checksum_i350(struct e1000_hw *hw); static s32 e1000_update_nvm_checksum_i350(struct e1000_hw *hw); static void e1000_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value); static void e1000_clear_vfta_i350(struct e1000_hw *hw); static const u16 e1000_82580_rxpbs_table[] = {36, 72, 144, 1, 2, 4, 8, 16, 35, 70, 140}; #define E1000_82580_RXPBS_TABLE_SIZE \ (sizeof (e1000_82580_rxpbs_table)/sizeof (u16)) /* * e1000_init_phy_params_82575 - Init PHY func ptrs. * @hw: pointer to the HW structure */ static s32 e1000_init_phy_params_82575(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val = E1000_SUCCESS; DEBUGFUNC("e1000_init_phy_params_82575"); if (hw->phy.media_type != e1000_media_type_copper) { phy->type = e1000_phy_none; goto out; } phy->ops.power_up = e1000_power_up_phy_copper; phy->ops.power_down = e1000_power_down_phy_copper_82575; phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; phy->reset_delay_us = 100; phy->ops.acquire = e1000_acquire_phy_82575; phy->ops.check_reset_block = e1000_check_reset_block_generic; phy->ops.commit = e1000_phy_sw_reset_generic; phy->ops.get_cfg_done = e1000_get_cfg_done_82575; phy->ops.release = e1000_release_phy_82575; if (e1000_sgmii_active_82575(hw)) { phy->ops.reset = e1000_phy_hw_reset_sgmii_82575; phy->ops.read_reg = e1000_read_phy_reg_sgmii_82575; phy->ops.write_reg = e1000_write_phy_reg_sgmii_82575; } else if (hw->mac.type == e1000_82580) { phy->ops.reset = e1000_phy_hw_reset_generic; phy->ops.read_reg = e1000_read_phy_reg_82580; phy->ops.write_reg = e1000_write_phy_reg_82580; } else { phy->ops.reset = e1000_phy_hw_reset_generic; phy->ops.read_reg = e1000_read_phy_reg_igp; phy->ops.write_reg = e1000_write_phy_reg_igp; } /* Set phy->phy_addr and phy->id. */ ret_val = e1000_get_phy_id_82575(hw); /* Verify phy id and set remaining function pointers */ switch (phy->id) { case M88E1111_I_PHY_ID: phy->type = e1000_phy_m88; phy->ops.check_polarity = e1000_check_polarity_m88; phy->ops.get_info = e1000_get_phy_info_m88; phy->ops.get_cable_length = e1000_get_cable_length_m88; phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; break; case IGP03E1000_E_PHY_ID: case IGP04E1000_E_PHY_ID: phy->type = e1000_phy_igp_3; phy->ops.check_polarity = e1000_check_polarity_igp; phy->ops.get_info = e1000_get_phy_info_igp; phy->ops.get_cable_length = e1000_get_cable_length_igp_2; phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82575; phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; break; case I82580_I_PHY_ID: case I350_I_PHY_ID: phy->type = e1000_phy_82580; phy->ops.check_polarity = e1000_check_polarity_82577; phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_82577; phy->ops.get_cable_length = e1000_get_cable_length_82577; phy->ops.get_info = e1000_get_phy_info_82577; break; default: ret_val = -E1000_ERR_PHY; goto out; } out: return (ret_val); } /* * e1000_init_nvm_params_82575 - Init NVM func ptrs. * @hw: pointer to the HW structure */ static s32 e1000_init_nvm_params_82575(struct e1000_hw *hw) { struct e1000_nvm_info *nvm = &hw->nvm; u32 eecd = E1000_READ_REG(hw, E1000_EECD); u16 size; DEBUGFUNC("e1000_init_nvm_params_82575"); nvm->opcode_bits = 8; nvm->delay_usec = 1; switch (nvm->override) { case e1000_nvm_override_spi_large: nvm->page_size = 32; nvm->address_bits = 16; break; case e1000_nvm_override_spi_small: nvm->page_size = 8; nvm->address_bits = 8; break; default: nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; break; } nvm->type = e1000_nvm_eeprom_spi; size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> E1000_EECD_SIZE_EX_SHIFT); /* * Added to a constant, "size" becomes the left-shift value * for setting word_size. */ size += NVM_WORD_SIZE_BASE_SHIFT; /* EEPROM access above 16k is unsupported */ if (size > 14) size = 14; nvm->word_size = 1 << size; /* Function Pointers */ nvm->ops.acquire = e1000_acquire_nvm_82575; nvm->ops.read = e1000_read_nvm_eerd; nvm->ops.release = e1000_release_nvm_82575; nvm->ops.update = e1000_update_nvm_checksum_generic; nvm->ops.valid_led_default = e1000_valid_led_default_82575; nvm->ops.validate = e1000_validate_nvm_checksum_generic; nvm->ops.write = e1000_write_nvm_spi; /* override genric family function pointers for specific descendants */ switch (hw->mac.type) { case e1000_i350: nvm->ops.validate = e1000_validate_nvm_checksum_i350; nvm->ops.update = e1000_update_nvm_checksum_i350; break; default: break; } return (E1000_SUCCESS); } /* * e1000_init_mac_params_82575 - Init MAC func ptrs. * @hw: pointer to the HW structure */ static s32 e1000_init_mac_params_82575(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; u32 ctrl_ext = 0; DEBUGFUNC("e1000_init_mac_params_82575"); /* Set media type */ /* * The 82575 uses bits 22:23 for link mode. The mode can be changed * based on the EEPROM. We cannot rely upon device ID. There * is no distinguishable difference between fiber and internal * SerDes mode on the 82575. There can be an external PHY attached * on the SGMII interface. For this, we'll set sgmii_active to true. */ hw->phy.media_type = e1000_media_type_copper; dev_spec->sgmii_active = false; ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { case E1000_CTRL_EXT_LINK_MODE_SGMII: dev_spec->sgmii_active = true; ctrl_ext |= E1000_CTRL_I2C_ENA; break; case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: hw->phy.media_type = e1000_media_type_internal_serdes; ctrl_ext |= E1000_CTRL_I2C_ENA; break; default: ctrl_ext &= ~E1000_CTRL_I2C_ENA; break; } E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); /* * if using i2c make certain the MDICNFG register is cleared to prevent * communications from being misrouted to the mdic registers */ if ((ctrl_ext & E1000_CTRL_I2C_ENA) && (hw->mac.type == e1000_82580)) E1000_WRITE_REG(hw, E1000_MDICNFG, 0); /* Set mta register count */ mac->mta_reg_count = 128; /* Set uta register count */ mac->uta_reg_count = (hw->mac.type == e1000_82575) ? 0 : 128; /* Set rar entry count */ mac->rar_entry_count = E1000_RAR_ENTRIES_82575; if (mac->type == e1000_82576) mac->rar_entry_count = E1000_RAR_ENTRIES_82576; if (mac->type == e1000_82580) mac->rar_entry_count = E1000_RAR_ENTRIES_82580; if (mac->type == e1000_i350) { mac->rar_entry_count = E1000_RAR_ENTRIES_I350; /* Enable EEE default settings for i350 */ dev_spec->eee_disable = B_FALSE; } /* Set if part includes ASF firmware */ mac->asf_firmware_present = true; /* Set if manageability features are enabled. */ mac->arc_subsystem_valid = (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) ? true : false; /* Function pointers */ /* bus type/speed/width */ mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; /* reset */ if (mac->type == e1000_82580) mac->ops.reset_hw = e1000_reset_hw_82580; else mac->ops.reset_hw = e1000_reset_hw_82575; /* hw initialization */ mac->ops.init_hw = e1000_init_hw_82575; /* link setup */ mac->ops.setup_link = e1000_setup_link_generic; /* physical interface link setup */ mac->ops.setup_physical_interface = (hw->phy.media_type == e1000_media_type_copper) ? e1000_setup_copper_link_82575 : e1000_setup_serdes_link_82575; /* physical interface shutdown */ mac->ops.shutdown_serdes = e1000_shutdown_serdes_link_82575; /* check for link */ mac->ops.check_for_link = e1000_check_for_link_82575; /* receive address register setting */ mac->ops.rar_set = e1000_rar_set_generic; /* read mac address */ mac->ops.read_mac_addr = e1000_read_mac_addr_82575; /* multicast address update */ mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; if (hw->mac.type == e1000_i350) { /* writing VFTA */ mac->ops.write_vfta = e1000_write_vfta_i350; /* clearing VFTA */ mac->ops.clear_vfta = e1000_clear_vfta_i350; } else { /* writing VFTA */ mac->ops.write_vfta = e1000_write_vfta_generic; /* clearing VFTA */ mac->ops.clear_vfta = e1000_clear_vfta_generic; } /* setting MTA */ mac->ops.mta_set = e1000_mta_set_generic; /* ID LED init */ mac->ops.id_led_init = e1000_id_led_init_generic; /* blink LED */ mac->ops.blink_led = e1000_blink_led_generic; /* setup LED */ mac->ops.setup_led = e1000_setup_led_generic; /* cleanup LED */ mac->ops.cleanup_led = e1000_cleanup_led_generic; /* turn on/off LED */ mac->ops.led_on = e1000_led_on_generic; mac->ops.led_off = e1000_led_off_generic; /* clear hardware counters */ mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82575; /* link info */ mac->ops.get_link_up_info = e1000_get_link_up_info_82575; /* set lan id for port to determine which phy lock to use */ hw->mac.ops.set_lan_id(hw); return (E1000_SUCCESS); } /* * e1000_init_function_pointers_82575 - Init func ptrs. * @hw: pointer to the HW structure * * Called to initialize all function pointers and parameters. */ void e1000_init_function_pointers_82575(struct e1000_hw *hw) { DEBUGFUNC("e1000_init_function_pointers_82575"); hw->mac.ops.init_params = e1000_init_mac_params_82575; hw->nvm.ops.init_params = e1000_init_nvm_params_82575; hw->phy.ops.init_params = e1000_init_phy_params_82575; } /* * e1000_acquire_phy_82575 - Acquire rights to access PHY * @hw: pointer to the HW structure * * Acquire access rights to the correct PHY. */ static s32 e1000_acquire_phy_82575(struct e1000_hw *hw) { u16 mask = E1000_SWFW_PHY0_SM; DEBUGFUNC("e1000_acquire_phy_82575"); if (hw->bus.func == E1000_FUNC_1) mask = E1000_SWFW_PHY1_SM; else if (hw->bus.func == E1000_FUNC_2) mask = E1000_SWFW_PHY2_SM; else if (hw->bus.func == E1000_FUNC_3) mask = E1000_SWFW_PHY3_SM; return (e1000_acquire_swfw_sync_82575(hw, mask)); } /* * e1000_release_phy_82575 - Release rights to access PHY * @hw: pointer to the HW structure * * A wrapper to release access rights to the correct PHY. */ static void e1000_release_phy_82575(struct e1000_hw *hw) { u16 mask = E1000_SWFW_PHY0_SM; DEBUGFUNC("e1000_release_phy_82575"); if (hw->bus.func == E1000_FUNC_1) mask = E1000_SWFW_PHY1_SM; else if (hw->bus.func == E1000_FUNC_2) mask = E1000_SWFW_PHY2_SM; else if (hw->bus.func == E1000_FUNC_3) mask = E1000_SWFW_PHY3_SM; e1000_release_swfw_sync_82575(hw, mask); } /* * e1000_read_phy_reg_sgmii_82575 - Read PHY register using sgmii * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the PHY register at offset using the serial gigabit media independent * interface and stores the retrieved information in data. */ static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, u16 *data) { s32 ret_val = -E1000_ERR_PARAM; DEBUGFUNC("e1000_read_phy_reg_sgmii_82575"); if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { DEBUGOUT1("PHY Address %u is out of range\n", offset); goto out; } ret_val = hw->phy.ops.acquire(hw); if (ret_val) goto out; ret_val = e1000_read_phy_reg_i2c(hw, offset, data); hw->phy.ops.release(hw); out: return (ret_val); } /* * e1000_write_phy_reg_sgmii_82575 - Write PHY register using sgmii * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Writes the data to PHY register at the offset using the serial gigabit * media independent interface. */ static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, u16 data) { s32 ret_val = -E1000_ERR_PARAM; DEBUGFUNC("e1000_write_phy_reg_sgmii_82575"); if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { DEBUGOUT1("PHY Address %d is out of range\n", offset); goto out; } ret_val = hw->phy.ops.acquire(hw); if (ret_val) goto out; ret_val = e1000_write_phy_reg_i2c(hw, offset, data); hw->phy.ops.release(hw); out: return (ret_val); } /* * e1000_get_phy_id_82575 - Retrieve PHY addr and id * @hw: pointer to the HW structure * * Retrieves the PHY address and ID for both PHY's which do and do not use * sgmi interface. */ static s32 e1000_get_phy_id_82575(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val = E1000_SUCCESS; u16 phy_id; u32 ctrl_ext; DEBUGFUNC("e1000_get_phy_id_82575"); /* * For SGMII PHYs, we try the list of possible addresses until * we find one that works. For non-SGMII PHYs * (e.g. integrated copper PHYs), an address of 1 should * work. The result of this function should mean phy->phy_addr * and phy->id are set correctly. */ if (!e1000_sgmii_active_82575(hw)) { phy->addr = 1; ret_val = e1000_get_phy_id(hw); goto out; } /* Power on sgmii phy if it is disabled */ ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA); E1000_WRITE_FLUSH(hw); msec_delay(300); /* * The address field in the I2CCMD register is 3 bits and 0 is invalid. * Therefore, we need to test 1-7 */ for (phy->addr = 1; phy->addr < 8; phy->addr++) { ret_val = e1000_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id); if (ret_val == E1000_SUCCESS) { DEBUGOUT2("Vendor ID 0x%08X read at address %u\n", phy_id, phy->addr); /* * At the time of this writing, The M88 part is * the only supported SGMII PHY product. */ if (phy_id == M88_VENDOR) break; } else { DEBUGOUT1("PHY address %u was unreadable\n", phy->addr); } } /* A valid PHY type couldn't be found. */ if (phy->addr == 8) { phy->addr = 0; ret_val = -E1000_ERR_PHY; } else { ret_val = e1000_get_phy_id(hw); } /* restore previous sfp cage power state */ E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); out: return (ret_val); } /* * e1000_phy_hw_reset_sgmii_82575 - Performs a PHY reset * @hw: pointer to the HW structure * * Resets the PHY using the serial gigabit media independent interface. */ static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; DEBUGFUNC("e1000_phy_hw_reset_sgmii_82575"); /* * This isn't a true "hard" reset, but is the only reset * available to us at this time. */ DEBUGOUT("Soft resetting SGMII attached PHY...\n"); if (!(hw->phy.ops.write_reg)) goto out; /* * SFP documentation requires the following to configure the SPF module * to work on SGMII. No further documentation is given. */ ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084); if (ret_val) goto out; ret_val = hw->phy.ops.commit(hw); out: return (ret_val); } /* * e1000_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state * @hw: pointer to the HW structure * @active: true to enable LPLU, false to disable * * Sets the LPLU D0 state according to the active flag. When * activating LPLU this function also disables smart speed * and vice versa. LPLU will not be activated unless the * device autonegotiation advertisement meets standards of * either 10 or 10/100 or 10/100/1000 at all duplexes. * This is a function pointer entry point only called by * PHY setup routines. */ static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val = E1000_SUCCESS; u16 data; DEBUGFUNC("e1000_set_d0_lplu_state_82575"); if (!(hw->phy.ops.read_reg)) goto out; ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); if (ret_val) goto out; if (active) { data |= IGP02E1000_PM_D0_LPLU; ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, data); if (ret_val) goto out; /* When LPLU is enabled, we should disable SmartSpeed */ ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &data); data &= ~IGP01E1000_PSCFR_SMART_SPEED; ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, data); if (ret_val) goto out; } else { data &= ~IGP02E1000_PM_D0_LPLU; ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, data); /* * LPLU and SmartSpeed are mutually exclusive. LPLU is used * during Dx states where the power conservation is most * important. During driver activity we should enable * SmartSpeed, so performance is maintained. */ if (phy->smart_speed == e1000_smart_speed_on) { ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &data); if (ret_val) goto out; data |= IGP01E1000_PSCFR_SMART_SPEED; ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, data); if (ret_val) goto out; } else if (phy->smart_speed == e1000_smart_speed_off) { ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &data); if (ret_val) goto out; data &= ~IGP01E1000_PSCFR_SMART_SPEED; ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, data); if (ret_val) goto out; } } out: return (ret_val); } /* * e1000_acquire_nvm_82575 - Request for access to EEPROM * @hw: pointer to the HW structure * * Acquire the necessary semaphores for exclusive access to the EEPROM. * Set the EEPROM access request bit and wait for EEPROM access grant bit. * Return successful if access grant bit set, else clear the request for * EEPROM access and return -E1000_ERR_NVM (-1). */ static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw) { s32 ret_val; DEBUGFUNC("e1000_acquire_nvm_82575"); ret_val = e1000_acquire_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); if (ret_val) goto out; /* * Check if there is some access * error this access may hook on */ if (hw->mac.type == e1000_i350) { u32 eecd = E1000_READ_REG(hw, E1000_EECD); if (eecd & (E1000_EECD_BLOCKED | E1000_EECD_ABORT | E1000_EECD_TIMEOUT)) { /* Clear all access error flags */ E1000_WRITE_REG(hw, E1000_EECD, eecd | E1000_EECD_ERROR_CLR); DEBUGOUT("Nvm bit banging access error " "detected and cleared.\n"); } } ret_val = e1000_acquire_nvm_generic(hw); if (ret_val) e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); out: return (ret_val); } /* * e1000_release_nvm_82575 - Release exclusive access to EEPROM * @hw: pointer to the HW structure * * Stop any current commands to the EEPROM and clear the EEPROM request bit, * then release the semaphores acquired. */ static void e1000_release_nvm_82575(struct e1000_hw *hw) { DEBUGFUNC("e1000_release_nvm_82575"); e1000_release_nvm_generic(hw); e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); } /* * e1000_acquire_swfw_sync_82575 - Acquire SW/FW semaphore * @hw: pointer to the HW structure * @mask: specifies which semaphore to acquire * * Acquire the SW/FW semaphore to access the PHY or NVM. The mask * will also specify which port we're acquiring the lock for. */ static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask) { u32 swfw_sync; u32 swmask = mask; u32 fwmask = mask << 16; s32 ret_val = E1000_SUCCESS; s32 i = 0, timeout = 200; /* FIXME: find real value to use here */ DEBUGFUNC("e1000_acquire_swfw_sync_82575"); while (i < timeout) { if (e1000_get_hw_semaphore_generic(hw)) { ret_val = -E1000_ERR_SWFW_SYNC; goto out; } swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); if (!(swfw_sync & (fwmask | swmask))) break; /* * Firmware currently using resource (fwmask) * or other software thread using resource (swmask) */ e1000_put_hw_semaphore_generic(hw); msec_delay_irq(5); i++; } if (i == timeout) { DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); ret_val = -E1000_ERR_SWFW_SYNC; goto out; } swfw_sync |= swmask; E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); e1000_put_hw_semaphore_generic(hw); out: return (ret_val); } /* * e1000_release_swfw_sync_82575 - Release SW/FW semaphore * @hw: pointer to the HW structure * @mask: specifies which semaphore to acquire * * Release the SW/FW semaphore used to access the PHY or NVM. The mask * will also specify which port we're releasing the lock for. */ static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask) { u32 swfw_sync; DEBUGFUNC("e1000_release_swfw_sync_82575"); while (e1000_get_hw_semaphore_generic(hw) != E1000_SUCCESS) { /* Empty */ } swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); swfw_sync &= ~mask; E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); e1000_put_hw_semaphore_generic(hw); } /* * e1000_get_cfg_done_82575 - Read config done bit * @hw: pointer to the HW structure * * Read the management control register for the config done bit for * completion status. NOTE: silicon which is EEPROM-less will fail trying * to read the config done bit, so an error is *ONLY* logged and returns * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon * would not be able to be reset or change link. */ static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw) { s32 timeout = PHY_CFG_TIMEOUT; s32 ret_val = E1000_SUCCESS; u32 mask = E1000_NVM_CFG_DONE_PORT_0; DEBUGFUNC("e1000_get_cfg_done_82575"); if (hw->bus.func == E1000_FUNC_1) mask = E1000_NVM_CFG_DONE_PORT_1; else if (hw->bus.func == E1000_FUNC_2) mask = E1000_NVM_CFG_DONE_PORT_2; else if (hw->bus.func == E1000_FUNC_3) mask = E1000_NVM_CFG_DONE_PORT_3; while (timeout) { if (E1000_READ_REG(hw, E1000_EEMNGCTL) & mask) break; msec_delay(1); timeout--; } if (!timeout) DEBUGOUT("MNG configuration cycle has not completed.\n"); /* If EEPROM is not marked present, init the PHY manually */ if (((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) && (hw->phy.type == e1000_phy_igp_3)) (void) e1000_phy_init_script_igp3(hw); return (ret_val); } /* * e1000_get_link_up_info_82575 - Get link speed/duplex info * @hw: pointer to the HW structure * @speed: stores the current speed * @duplex: stores the current duplex * * This is a wrapper function, if using the serial gigabit media independent * interface, use PCS to retrieve the link speed and duplex information. * Otherwise, use the generic function to get the link speed and duplex info. */ static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, u16 *duplex) { s32 ret_val; DEBUGFUNC("e1000_get_link_up_info_82575"); if (hw->phy.media_type != e1000_media_type_copper) ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, speed, duplex); else ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, duplex); return (ret_val); } /* * e1000_check_for_link_82575 - Check for link * @hw: pointer to the HW structure * * If sgmii is enabled, then use the pcs register to determine link, otherwise * use the generic interface for determining link. */ static s32 e1000_check_for_link_82575(struct e1000_hw *hw) { s32 ret_val; u16 speed, duplex; DEBUGFUNC("e1000_check_for_link_82575"); /* SGMII link check is done through the PCS register. */ if (hw->phy.media_type != e1000_media_type_copper) { ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, &speed, &duplex); /* * Use this flag to determine if link needs to be checked or * not. If we have link clear the flag so that we do not * continue to check for link. */ hw->mac.get_link_status = !hw->mac.serdes_has_link; } else { ret_val = e1000_check_for_copper_link_generic(hw); } return (ret_val); } /* * e1000_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex * @hw: pointer to the HW structure * @speed: stores the current speed * @duplex: stores the current duplex * * Using the physical coding sub-layer (PCS), retrieve the current speed and * duplex, then store the values in the pointers provided. */ static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed, u16 *duplex) { struct e1000_mac_info *mac = &hw->mac; u32 pcs; DEBUGFUNC("e1000_get_pcs_speed_and_duplex_82575"); /* Set up defaults for the return values of this function */ mac->serdes_has_link = false; *speed = 0; *duplex = 0; /* * Read the PCS Status register for link state. For non-copper mode, * the status register is not accurate. The PCS status register is * used instead. */ pcs = E1000_READ_REG(hw, E1000_PCS_LSTAT); /* * The link up bit determines when link is up on autoneg. The sync ok * gets set once both sides sync up and agree upon link. Stable link * can be determined by checking for both link up and link sync ok */ if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) { mac->serdes_has_link = true; /* Detect and store PCS speed */ if (pcs & E1000_PCS_LSTS_SPEED_1000) { *speed = SPEED_1000; } else if (pcs & E1000_PCS_LSTS_SPEED_100) { *speed = SPEED_100; } else { *speed = SPEED_10; } /* Detect and store PCS duplex */ if (pcs & E1000_PCS_LSTS_DUPLEX_FULL) { *duplex = FULL_DUPLEX; } else { *duplex = HALF_DUPLEX; } } return (E1000_SUCCESS); } /* * e1000_shutdown_serdes_link_82575 - Remove link during power down * @hw: pointer to the HW structure * * In the case of serdes shut down sfp and PCS on driver unload * when management pass thru is not enabled. */ void e1000_shutdown_serdes_link_82575(struct e1000_hw *hw) { u32 reg; u16 eeprom_data = 0; if ((hw->phy.media_type != e1000_media_type_internal_serdes) && !e1000_sgmii_active_82575(hw)) return; if (hw->bus.func == E1000_FUNC_0) hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data); else if (hw->mac.type == e1000_82580) hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, &eeprom_data); else if (hw->bus.func == E1000_FUNC_1) hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); /* * If APM is not enabled in the EEPROM and management interface is * not enabled, then power down. */ if (!(eeprom_data & E1000_NVM_APME_82575) && !e1000_enable_mng_pass_thru(hw)) { /* Disable PCS to turn off link */ reg = E1000_READ_REG(hw, E1000_PCS_CFG0); reg &= ~E1000_PCS_CFG_PCS_EN; E1000_WRITE_REG(hw, E1000_PCS_CFG0, reg); /* shutdown the laser */ reg = E1000_READ_REG(hw, E1000_CTRL_EXT); reg |= E1000_CTRL_EXT_SDP3_DATA; E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); /* flush the write to verify completion */ E1000_WRITE_FLUSH(hw); msec_delay(1); } } /* * e1000_reset_hw_82575 - Reset hardware * @hw: pointer to the HW structure * * This resets the hardware into a known state. */ static s32 e1000_reset_hw_82575(struct e1000_hw *hw) { u32 ctrl; s32 ret_val; DEBUGFUNC("e1000_reset_hw_82575"); /* * Prevent the PCI-E bus from sticking if there is no TLP connection * on the last TLP read/write transaction when MAC is reset. */ ret_val = e1000_disable_pcie_master_generic(hw); if (ret_val) { DEBUGOUT("PCI-E Master disable polling has failed.\n"); } /* set the completion timeout for interface */ ret_val = e1000_set_pcie_completion_timeout(hw); if (ret_val) { DEBUGOUT("PCI-E Set completion timeout has failed.\n"); } DEBUGOUT("Masking off all interrupts\n"); E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); E1000_WRITE_REG(hw, E1000_RCTL, 0); E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); E1000_WRITE_FLUSH(hw); msec_delay(10); ctrl = E1000_READ_REG(hw, E1000_CTRL); DEBUGOUT("Issuing a global reset to MAC\n"); E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); ret_val = e1000_get_auto_rd_done_generic(hw); if (ret_val) { /* * When auto config read does not complete, do not * return with an error. This can happen in situations * where there is no eeprom and prevents getting link. */ DEBUGOUT("Auto Read Done did not complete\n"); } /* If EEPROM is not present, run manual init scripts */ if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) (void) e1000_reset_init_script_82575(hw); /* Clear any pending interrupt events. */ E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); (void) E1000_READ_REG(hw, E1000_ICR); /* Install any alternate MAC address into RAR0 */ ret_val = e1000_check_alt_mac_addr_generic(hw); return (ret_val); } /* * e1000_init_hw_82575 - Initialize hardware * @hw: pointer to the HW structure * * This inits the hardware readying it for operation. */ static s32 e1000_init_hw_82575(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; s32 ret_val; u16 i, rar_count = mac->rar_entry_count; DEBUGFUNC("e1000_init_hw_82575"); /* Initialize identification LED */ ret_val = mac->ops.id_led_init(hw); if (ret_val) { DEBUGOUT("Error initializing identification LED\n"); /* This is not fatal and we should not stop init due to this */ } /* Disabling VLAN filtering */ DEBUGOUT("Initializing the IEEE VLAN\n"); mac->ops.clear_vfta(hw); /* Setup the receive address */ e1000_init_rx_addrs_generic(hw, rar_count); /* Zero out the Multicast HASH table */ DEBUGOUT("Zeroing the MTA\n"); for (i = 0; i < mac->mta_reg_count; i++) E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); /* Zero out the Unicast HASH table */ DEBUGOUT("Zeroing the UTA\n"); for (i = 0; i < mac->uta_reg_count; i++) E1000_WRITE_REG_ARRAY(hw, E1000_UTA, i, 0); /* Setup link and flow control */ ret_val = mac->ops.setup_link(hw); /* * Clear all of the statistics registers (clear on read). It is * important that we do this after we have tried to establish link * because the symbol error count will increment wildly if there * is no link. */ e1000_clear_hw_cntrs_82575(hw); return (ret_val); } /* * e1000_setup_copper_link_82575 - Configure copper link settings * @hw: pointer to the HW structure * * Configures the link for auto-neg or forced speed and duplex. Then we check * for link, once link is established calls to configure collision distance * and flow control are called. */ static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw) { u32 ctrl; s32 ret_val; DEBUGFUNC("e1000_setup_copper_link_82575"); ctrl = E1000_READ_REG(hw, E1000_CTRL); ctrl |= E1000_CTRL_SLU; ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); E1000_WRITE_REG(hw, E1000_CTRL, ctrl); ret_val = e1000_setup_serdes_link_82575(hw); if (ret_val) goto out; if (e1000_sgmii_active_82575(hw) && !hw->phy.reset_disable) { /* allow time for SFP cage time to power up phy */ msec_delay(300); ret_val = hw->phy.ops.reset(hw); if (ret_val) { DEBUGOUT("Error resetting the PHY.\n"); goto out; } } switch (hw->phy.type) { case e1000_phy_m88: ret_val = e1000_copper_link_setup_m88(hw); break; case e1000_phy_igp_3: ret_val = e1000_copper_link_setup_igp(hw); break; case e1000_phy_82580: ret_val = e1000_copper_link_setup_82577(hw); break; default: ret_val = -E1000_ERR_PHY; break; } if (ret_val) goto out; ret_val = e1000_setup_copper_link_generic(hw); out: return (ret_val); } /* * e1000_setup_serdes_link_82575 - Setup link for serdes * @hw: pointer to the HW structure * * Configure the physical coding sub-layer (PCS) link. The PCS link is * used on copper connections where the serialized gigabit media independent * interface (sgmii), or serdes fiber is being used. Configures the link * for auto-negotiation or forces speed/duplex. */ static s32 e1000_setup_serdes_link_82575(struct e1000_hw *hw) { u32 ctrl_ext, ctrl_reg, reg; bool pcs_autoneg; DEBUGFUNC("e1000_setup_serdes_link_82575"); if ((hw->phy.media_type != e1000_media_type_internal_serdes) && !e1000_sgmii_active_82575(hw)) return (E1000_SUCCESS); /* * On the 82575, SerDes loopback mode persists until it is * explicitly turned off or a power cycle is performed. A read to * the register does not indicate its status. Therefore, we ensure * loopback mode is disabled during initialization. */ E1000_WRITE_REG(hw, E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); /* power on the sfp cage if present */ ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); ctrl_reg = E1000_READ_REG(hw, E1000_CTRL); ctrl_reg |= E1000_CTRL_SLU; if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) { /* set both sw defined pins */ ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1; /* Set switch control to serdes energy detect */ reg = E1000_READ_REG(hw, E1000_CONNSW); reg |= E1000_CONNSW_ENRGSRC; E1000_WRITE_REG(hw, E1000_CONNSW, reg); } reg = E1000_READ_REG(hw, E1000_PCS_LCTL); /* default pcs_autoneg to the same setting as mac autoneg */ pcs_autoneg = hw->mac.autoneg; switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { case E1000_CTRL_EXT_LINK_MODE_SGMII: /* sgmii mode lets the phy handle forcing speed/duplex */ pcs_autoneg = true; /* autoneg time out should be disabled for SGMII mode */ reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); break; case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: /* disable PCS autoneg and support parallel detect only */ pcs_autoneg = false; default: /* * non-SGMII modes only supports a speed of 1000/Full for the * link so it is best to just force the MAC and let the pcs * link either autoneg or be forced to 1000/Full */ ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD | E1000_CTRL_FD | E1000_CTRL_FRCDPX; /* set speed of 1000/Full if speed/duplex is forced */ reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL; break; } E1000_WRITE_REG(hw, E1000_CTRL, ctrl_reg); /* * New SerDes mode allows for forcing speed or autonegotiating speed * at 1gb. Autoneg should be default set by most drivers. This is the * mode that will be compatible with older link partners and switches. * However, both are supported by the hardware and some drivers/tools. */ reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); /* * We force flow control to prevent the CTRL register values from being * overwritten by the autonegotiated flow control values */ reg |= E1000_PCS_LCTL_FORCE_FCTRL; if (pcs_autoneg) { /* Set PCS register for autoneg */ reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ DEBUGOUT1("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg); } else { /* Set PCS register for forced link */ reg |= E1000_PCS_LCTL_FSD; /* Force Speed */ DEBUGOUT1("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg); } E1000_WRITE_REG(hw, E1000_PCS_LCTL, reg); if (!e1000_sgmii_active_82575(hw)) (void) e1000_force_mac_fc_generic(hw); return (E1000_SUCCESS); } /* * e1000_valid_led_default_82575 - Verify a valid default LED config * @hw: pointer to the HW structure * @data: pointer to the NVM (EEPROM) * * Read the EEPROM for the current default LED configuration. If the * LED configuration is not valid, set to a valid LED configuration. */ static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data) { s32 ret_val; DEBUGFUNC("e1000_valid_led_default_82575"); ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); if (ret_val) { DEBUGOUT("NVM Read Error\n"); goto out; } if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) { switch (hw->phy.media_type) { case e1000_media_type_internal_serdes: *data = ID_LED_DEFAULT_82575_SERDES; break; case e1000_media_type_copper: default: *data = ID_LED_DEFAULT; break; } } out: return (ret_val); } /* * e1000_sgmii_active_82575 - Return sgmii state * @hw: pointer to the HW structure * * 82575 silicon has a serialized gigabit media independent interface (sgmii) * which can be enabled for use in the embedded applications. Simply * return the current state of the sgmii interface. */ static bool e1000_sgmii_active_82575(struct e1000_hw *hw) { struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; return (dev_spec->sgmii_active); } /* * e1000_reset_init_script_82575 - Inits HW defaults after reset * @hw: pointer to the HW structure * * Inits recommended HW defaults after a reset when there is no EEPROM * detected. This is only for the 82575. */ static s32 e1000_reset_init_script_82575(struct e1000_hw *hw) { DEBUGFUNC("e1000_reset_init_script_82575"); if (hw->mac.type == e1000_82575) { DEBUGOUT("Running reset init script for 82575\n"); /* SerDes configuration via SERDESCTRL */ (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x00, 0x0C); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x01, 0x78); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x1B, 0x23); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x23, 0x15); /* CCM configuration via CCMCTL register */ (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x14, 0x00); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x10, 0x00); /* PCIe lanes configuration */ (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x00, 0xEC); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x61, 0xDF); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x34, 0x05); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x2F, 0x81); /* PCIe PLL Configuration */ (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x02, 0x47); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x14, 0x00); (void) e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x10, 0x00); } return (E1000_SUCCESS); } /* * e1000_read_mac_addr_82575 - Read device MAC address * @hw: pointer to the HW structure */ static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; DEBUGFUNC("e1000_read_mac_addr_82575"); /* * If there's an alternate MAC address place it in RAR0 * so that it will override the Si installed default perm * address. */ ret_val = e1000_check_alt_mac_addr_generic(hw); if (ret_val) goto out; ret_val = e1000_read_mac_addr_generic(hw); out: return (ret_val); } /* * e1000_power_down_phy_copper_82575 - Remove link during PHY power down * @hw: pointer to the HW structure * * In the case of a PHY power down to save power, or to turn off link during a * driver unload, or wake on lan is not enabled, remove the link. */ static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; struct e1000_mac_info *mac = &hw->mac; if (!(phy->ops.check_reset_block)) return; /* If the management interface is not enabled, then power down */ if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw))) e1000_power_down_phy_copper(hw); } /* * e1000_clear_hw_cntrs_82575 - Clear device specific hardware counters * @hw: pointer to the HW structure * * Clears the hardware counters by reading the counter registers. */ static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw) { DEBUGFUNC("e1000_clear_hw_cntrs_82575"); e1000_clear_hw_cntrs_base_generic(hw); (void) E1000_READ_REG(hw, E1000_PRC64); (void) E1000_READ_REG(hw, E1000_PRC127); (void) E1000_READ_REG(hw, E1000_PRC255); (void) E1000_READ_REG(hw, E1000_PRC511); (void) E1000_READ_REG(hw, E1000_PRC1023); (void) E1000_READ_REG(hw, E1000_PRC1522); (void) E1000_READ_REG(hw, E1000_PTC64); (void) E1000_READ_REG(hw, E1000_PTC127); (void) E1000_READ_REG(hw, E1000_PTC255); (void) E1000_READ_REG(hw, E1000_PTC511); (void) E1000_READ_REG(hw, E1000_PTC1023); (void) E1000_READ_REG(hw, E1000_PTC1522); (void) E1000_READ_REG(hw, E1000_ALGNERRC); (void) E1000_READ_REG(hw, E1000_RXERRC); (void) E1000_READ_REG(hw, E1000_TNCRS); (void) E1000_READ_REG(hw, E1000_CEXTERR); (void) E1000_READ_REG(hw, E1000_TSCTC); (void) E1000_READ_REG(hw, E1000_TSCTFC); (void) E1000_READ_REG(hw, E1000_MGTPRC); (void) E1000_READ_REG(hw, E1000_MGTPDC); (void) E1000_READ_REG(hw, E1000_MGTPTC); (void) E1000_READ_REG(hw, E1000_IAC); (void) E1000_READ_REG(hw, E1000_ICRXOC); (void) E1000_READ_REG(hw, E1000_ICRXPTC); (void) E1000_READ_REG(hw, E1000_ICRXATC); (void) E1000_READ_REG(hw, E1000_ICTXPTC); (void) E1000_READ_REG(hw, E1000_ICTXATC); (void) E1000_READ_REG(hw, E1000_ICTXQEC); (void) E1000_READ_REG(hw, E1000_ICTXQMTC); (void) E1000_READ_REG(hw, E1000_ICRXDMTC); (void) E1000_READ_REG(hw, E1000_CBTMPC); (void) E1000_READ_REG(hw, E1000_HTDPMC); (void) E1000_READ_REG(hw, E1000_CBRMPC); (void) E1000_READ_REG(hw, E1000_RPTHC); (void) E1000_READ_REG(hw, E1000_HGPTC); (void) E1000_READ_REG(hw, E1000_HTCBDPC); (void) E1000_READ_REG(hw, E1000_HGORCL); (void) E1000_READ_REG(hw, E1000_HGORCH); (void) E1000_READ_REG(hw, E1000_HGOTCL); (void) E1000_READ_REG(hw, E1000_HGOTCH); (void) E1000_READ_REG(hw, E1000_LENERRS); /* This register should not be read in copper configurations */ if ((hw->phy.media_type == e1000_media_type_internal_serdes) || e1000_sgmii_active_82575(hw)) (void) E1000_READ_REG(hw, E1000_SCVPC); } /* * e1000_rx_fifo_flush_82575 - Clean rx fifo after RX enable * @hw: pointer to the HW structure * * After rx enable if managability is enabled then there is likely some * bad data at the start of the fifo and possibly in the DMA fifo. This * function clears the fifos and flushes any packets that came in as rx was * being enabled. */ void e1000_rx_fifo_flush_82575(struct e1000_hw *hw) { u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; int i, ms_wait; DEBUGFUNC("e1000_rx_fifo_workaround_82575"); if (hw->mac.type != e1000_82575 || !(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_RCV_TCO_EN)) return; /* Disable all RX queues */ for (i = 0; i < 4; i++) { rxdctl[i] = E1000_READ_REG(hw, E1000_RXDCTL(i)); E1000_WRITE_REG(hw, E1000_RXDCTL(i), rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE); } /* Poll all queues to verify they have shut down */ for (ms_wait = 0; ms_wait < 10; ms_wait++) { msec_delay(1); rx_enabled = 0; for (i = 0; i < 4; i++) rx_enabled |= E1000_READ_REG(hw, E1000_RXDCTL(i)); if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE)) break; } if (ms_wait == 10) DEBUGOUT("Queue disable timed out after 10ms\n"); /* * Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all * incoming packets are rejected. Set enable and wait 2ms so that * any packet that was coming in as RCTL.EN was set is flushed */ rfctl = E1000_READ_REG(hw, E1000_RFCTL); E1000_WRITE_REG(hw, E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); rlpml = E1000_READ_REG(hw, E1000_RLPML); E1000_WRITE_REG(hw, E1000_RLPML, 0); rctl = E1000_READ_REG(hw, E1000_RCTL); temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP); temp_rctl |= E1000_RCTL_LPE; E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl); E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl | E1000_RCTL_EN); E1000_WRITE_FLUSH(hw); msec_delay(2); /* * Enable RX queues that were previously enabled and restore our * previous state */ for (i = 0; i < 4; i++) E1000_WRITE_REG(hw, E1000_RXDCTL(i), rxdctl[i]); E1000_WRITE_REG(hw, E1000_RCTL, rctl); E1000_WRITE_FLUSH(hw); E1000_WRITE_REG(hw, E1000_RLPML, rlpml); E1000_WRITE_REG(hw, E1000_RFCTL, rfctl); /* Flush receive errors generated by workaround */ (void) E1000_READ_REG(hw, E1000_ROC); (void) E1000_READ_REG(hw, E1000_RNBC); (void) E1000_READ_REG(hw, E1000_MPC); } /* * e1000_set_pcie_completion_timeout - set pci-e completion timeout * @hw: pointer to the HW structure * * The defaults for 82575 and 82576 should be in the range of 50us to 50ms, * however the hardware default for these parts is 500us to 1ms which is less * than the 10ms recommended by the pci-e spec. To address this we need to * increase the value to either 10ms to 200ms for capability version 1 config, * or 16ms to 55ms for version 2. */ static s32 e1000_set_pcie_completion_timeout(struct e1000_hw *hw) { u32 gcr = E1000_READ_REG(hw, E1000_GCR); s32 ret_val = E1000_SUCCESS; u16 pcie_devctl2; /* only take action if timeout value is defaulted to 0 */ if (gcr & E1000_GCR_CMPL_TMOUT_MASK) goto out; /* * if capababilities version is type 1 we can write the * timeout of 10ms to 200ms through the GCR register */ if (!(gcr & E1000_GCR_CAP_VER2)) { gcr |= E1000_GCR_CMPL_TMOUT_10ms; goto out; } /* * for version 2 capabilities we need to write the config space * directly in order to set the completion timeout value for * 16ms to 55ms */ ret_val = e1000_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, &pcie_devctl2); if (ret_val) goto out; pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms; ret_val = e1000_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, &pcie_devctl2); out: /* disable completion timeout resend */ gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND; E1000_WRITE_REG(hw, E1000_GCR, gcr); return (ret_val); } /* * e1000_vmdq_set_loopback_pf - enable or disable vmdq loopback * @hw: pointer to the hardware struct * @enable: state to enter, either enabled or disabled * * enables/disables L2 switch loopback functionality. */ void e1000_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable) { u32 dtxswc = E1000_READ_REG(hw, E1000_DTXSWC); if (enable) dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; else dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; E1000_WRITE_REG(hw, E1000_DTXSWC, dtxswc); } /* * e1000_vmdq_set_replication_pf - enable or disable vmdq replication * @hw: pointer to the hardware struct * @enable: state to enter, either enabled or disabled * * enables/disables replication of packets across multiple pools. */ void e1000_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable) { u32 vt_ctl = E1000_READ_REG(hw, E1000_VT_CTL); if (enable) vt_ctl |= E1000_VT_CTL_VM_REPL_EN; else vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN; E1000_WRITE_REG(hw, E1000_VT_CTL, vt_ctl); } /* * e1000_read_phy_reg_82580 - Read 82580 MDI control register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the MDI control register in the PHY at offset and stores the * information read to data. */ static s32 e1000_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data) { u32 mdicnfg = 0; s32 ret_val; DEBUGFUNC("e1000_read_phy_reg_82580"); ret_val = hw->phy.ops.acquire(hw); if (ret_val) goto out; /* * We config the phy address in MDICNFG register now. Same bits * as before. The values in MDIC can be written but will be * ignored. This allows us to call the old function after * configuring the PHY address in the new register */ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT); E1000_WRITE_REG(hw, E1000_MDICNFG, mdicnfg); ret_val = e1000_read_phy_reg_mdic(hw, offset, data); hw->phy.ops.release(hw); out: return (ret_val); } /* * e1000_write_phy_reg_82580 - Write 82580 MDI control register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write to register at offset * * Writes data to MDI control register in the PHY at offset. */ static s32 e1000_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data) { u32 mdicnfg = 0; s32 ret_val; DEBUGFUNC("e1000_write_phy_reg_82580"); ret_val = hw->phy.ops.acquire(hw); if (ret_val) goto out; /* * We config the phy address in MDICNFG register now. Same bits * as before. The values in MDIC can be written but will be * ignored. This allows us to call the old function after * configuring the PHY address in the new register */ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT); E1000_WRITE_REG(hw, E1000_MDICNFG, mdicnfg); ret_val = e1000_write_phy_reg_mdic(hw, offset, data); hw->phy.ops.release(hw); out: return (ret_val); } /* * e1000_reset_hw_82580 - Reset hardware * @hw: pointer to the HW structure * * This resets function or entire device (all ports, etc.) * to a known state. */ static s32 e1000_reset_hw_82580(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; /* BH SW mailbox bit in SW_FW_SYNC */ u16 swmbsw_mask = E1000_SW_SYNCH_MB; u32 ctrl; bool global_device_reset = hw->dev_spec._82575.global_device_reset; DEBUGFUNC("e1000_reset_hw_82580"); hw->dev_spec._82575.global_device_reset = false; /* Get current control state. */ ctrl = E1000_READ_REG(hw, E1000_CTRL); /* * Prevent the PCI-E bus from sticking if there is no TLP connection * on the last TLP read/write transaction when MAC is reset. */ ret_val = e1000_disable_pcie_master_generic(hw); if (ret_val) DEBUGOUT("PCI-E Master disable polling has failed.\n"); DEBUGOUT("Masking off all interrupts\n"); E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); E1000_WRITE_REG(hw, E1000_RCTL, 0); E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); E1000_WRITE_FLUSH(hw); msec_delay(10); /* Determine whether or not a global dev reset is requested */ if (global_device_reset && e1000_acquire_swfw_sync_82575(hw, swmbsw_mask)) global_device_reset = false; if (global_device_reset && !(E1000_READ_REG(hw, E1000_STATUS) & E1000_STAT_DEV_RST_SET)) ctrl |= E1000_CTRL_DEV_RST; else ctrl |= E1000_CTRL_RST; E1000_WRITE_REG(hw, E1000_CTRL, ctrl); /* Add delay to insure DEV_RST has time to complete */ if (global_device_reset) msec_delay(5); ret_val = e1000_get_auto_rd_done_generic(hw); if (ret_val) { /* * When auto config read does not complete, do not * return with an error. This can happen in situations * where there is no eeprom and prevents getting link. */ DEBUGOUT("Auto Read Done did not complete\n"); } /* If EEPROM is not present, run manual init scripts */ if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) (void) e1000_reset_init_script_82575(hw); /* clear global device reset status bit */ E1000_WRITE_REG(hw, E1000_STATUS, E1000_STAT_DEV_RST_SET); /* Clear any pending interrupt events. */ E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); (void) E1000_READ_REG(hw, E1000_ICR); /* Install any alternate MAC address into RAR0 */ ret_val = e1000_check_alt_mac_addr_generic(hw); /* Release semaphore */ if (global_device_reset) e1000_release_swfw_sync_82575(hw, swmbsw_mask); return (ret_val); } /* * e1000_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size * @data: data received by reading RXPBS register * * The 82580 uses a table based approach for packet buffer allocation sizes. * This function converts the retrieved value into the correct table value * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 * 0x0 36 72 144 1 2 4 8 16 * 0x8 35 70 140 rsv rsv rsv rsv rsv */ u16 e1000_rxpbs_adjust_82580(u32 data) { u16 ret_val = 0; if (data < E1000_82580_RXPBS_TABLE_SIZE) ret_val = e1000_82580_rxpbs_table[data]; return (ret_val); } /* * Due to a hw errata, if the host tries to configure the VFTA register * while performing queries from the BMC or DMA, then the VFTA in some * cases won't be written. */ /* * e1000_clear_vfta_i350 - Clear VLAN filter table * @hw: pointer to the HW structure * * Clears the register array which contains the VLAN filter table by * setting all the values to 0. */ void e1000_clear_vfta_i350(struct e1000_hw *hw) { u32 offset; int i; DEBUGFUNC("e1000_clear_vfta_350"); for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { for (i = 0; i < 10; i++) E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0); E1000_WRITE_FLUSH(hw); } } /* * e1000_write_vfta_i350 - Write value to VLAN filter table * @hw: pointer to the HW structure * @offset: register offset in VLAN filter table * @value: register value written to VLAN filter table * * Writes value at the given offset in the register array which stores * the VLAN filter table. */ void e1000_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value) { int i; DEBUGFUNC("e1000_write_vfta_350"); for (i = 0; i < 10; i++) E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value); E1000_WRITE_FLUSH(hw); } /* * e1000_validate_nvm_checksum_with_offset - Validate EEPROM * checksum * @hw: pointer to the HW structure * @offset: offset in words of the checksum protected region * * Calculates the EEPROM checksum by reading/adding each word of the EEPROM * and then verifies that the sum of the EEPROM is equal to 0xBABA. */ s32 e1000_validate_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) { s32 ret_val = E1000_SUCCESS; u16 checksum = 0; u16 i, nvm_data; DEBUGFUNC("e1000_validate_nvm_checksum_with_offset"); for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) { ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); if (ret_val) { DEBUGOUT("NVM Read Error\n"); goto out; } checksum += nvm_data; } if (checksum != (u16) NVM_SUM) { DEBUGOUT("NVM Checksum Invalid\n"); ret_val = -E1000_ERR_NVM; goto out; } out: return (ret_val); } /* * e1000_update_nvm_checksum_with_offset - Update EEPROM * checksum * @hw: pointer to the HW structure * @offset: offset in words of the checksum protected region * * Updates the EEPROM checksum by reading/adding each word of the EEPROM * up to the checksum. Then calculates the EEPROM checksum and writes the * value to the EEPROM. */ s32 e1000_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) { s32 ret_val; u16 checksum = 0; u16 i, nvm_data; DEBUGFUNC("e1000_update_nvm_checksum_with_offset"); for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) { ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); if (ret_val) { DEBUGOUT("NVM Read Error while updating checksum.\n"); goto out; } checksum += nvm_data; } checksum = (u16) NVM_SUM - checksum; ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1, &checksum); if (ret_val) DEBUGOUT("NVM Write Error while updating checksum.\n"); out: return (ret_val); } /* * e1000_validate_nvm_checksum_i350 - Validate EEPROM checksum * @hw: pointer to the HW structure * * Calculates the EEPROM section checksum by reading/adding each word of * the EEPROM and then verifies that the sum of the EEPROM is * equal to 0xBABA. */ static s32 e1000_validate_nvm_checksum_i350(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; u16 j; u16 nvm_offset; DEBUGFUNC("e1000_validate_nvm_checksum_i350"); for (j = 0; j < 4; j++) { nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); ret_val = e1000_validate_nvm_checksum_with_offset(hw, nvm_offset); if (ret_val != E1000_SUCCESS) goto out; } out: return (ret_val); } /* * e1000_update_nvm_checksum_i350 - Update EEPROM checksum * @hw: pointer to the HW structure * * Updates the EEPROM section checksums for all 4 ports by reading/adding * each word of the EEPROM up to the checksum. Then calculates the EEPROM * checksum and writes the value to the EEPROM. */ static s32 e1000_update_nvm_checksum_i350(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; u16 j; u16 nvm_offset; DEBUGFUNC("e1000_update_nvm_checksum_i350"); for (j = 0; j < 4; j++) { nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); ret_val = e1000_update_nvm_checksum_with_offset(hw, nvm_offset); if (ret_val != E1000_SUCCESS) goto out; } out: return (ret_val); } /* * e1000_set_eee_i350 - Enable/disable EEE support * @hw: pointer to the HW structure * * Enable/disable EEE based on setting in dev_spec structure. * */ s32 e1000_set_eee_i350(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; u32 ipcnfg, eeer; DEBUGFUNC("e1000_set_eee_i350"); if ((hw->mac.type < e1000_i350) || (hw->phy.media_type != e1000_media_type_copper)) goto out; ipcnfg = E1000_READ_REG(hw, E1000_IPCNFG); eeer = E1000_READ_REG(hw, E1000_EEER); /* enable or disable per user setting */ if (!(hw->dev_spec._82575.eee_disable)) { ipcnfg |= (E1000_IPCNFG_EEE_1G_AN | E1000_IPCNFG_EEE_100M_AN); eeer |= (E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN | E1000_EEER_LPI_FC); } else { ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN | E1000_IPCNFG_EEE_100M_AN); eeer &= ~(E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN | E1000_EEER_LPI_FC); } E1000_WRITE_REG(hw, E1000_IPCNFG, ipcnfg); E1000_WRITE_REG(hw, E1000_EEER, eeer); E1000_READ_REG(hw, E1000_IPCNFG); E1000_READ_REG(hw, E1000_EEER); out: return (ret_val); }