/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License, Version 1.0 only * (the "License"). You may not use this file except in compliance * with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2005 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #pragma ident "%Z%%M% %I% %E% SMI" /* * Sun4 PCI Express to PCI bus bridge nexus driver */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "pcie_pwr.h" #include "px_pci.h" #include "px_debug.h" /* * PXB MSI tunable: * * By default MSI is enabled on all supported platforms. */ boolean_t pxb_enable_msi = B_TRUE; static int pxb_bus_map(dev_info_t *, dev_info_t *, ddi_map_req_t *, off_t, off_t, caddr_t *); static int pxb_ctlops(dev_info_t *, dev_info_t *, ddi_ctl_enum_t, void *, void *); static int pxb_intr_ops(dev_info_t *dip, dev_info_t *rdip, ddi_intr_op_t intr_op, ddi_intr_handle_impl_t *hdlp, void *result); /* * FMA functions */ static int pxb_fm_init(pxb_devstate_t *pxb_p); static void pxb_fm_fini(pxb_devstate_t *pxb_p); static int pxb_fm_init_child(dev_info_t *dip, dev_info_t *cdip, int cap, ddi_iblock_cookie_t *ibc_p); static int pxb_fm_err_callback(dev_info_t *dip, ddi_fm_error_t *derr, const void *impl_data); struct bus_ops pxb_bus_ops = { BUSO_REV, pxb_bus_map, 0, 0, 0, i_ddi_map_fault, ddi_dma_map, ddi_dma_allochdl, ddi_dma_freehdl, ddi_dma_bindhdl, ddi_dma_unbindhdl, ddi_dma_flush, ddi_dma_win, ddi_dma_mctl, pxb_ctlops, ddi_bus_prop_op, ndi_busop_get_eventcookie, /* (*bus_get_eventcookie)(); */ ndi_busop_add_eventcall, /* (*bus_add_eventcall)(); */ ndi_busop_remove_eventcall, /* (*bus_remove_eventcall)(); */ ndi_post_event, /* (*bus_post_event)(); */ NULL, /* (*bus_intr_ctl)(); */ NULL, /* (*bus_config)(); */ NULL, /* (*bus_unconfig)(); */ pxb_fm_init_child, /* (*bus_fm_init)(); */ NULL, /* (*bus_fm_fini)(); */ i_ndi_busop_access_enter, /* (*bus_fm_access_enter)(); */ i_ndi_busop_access_exit, /* (*bus_fm_access_fini)(); */ pcie_bus_power, /* (*bus_power)(); */ pxb_intr_ops /* (*bus_intr_op)(); */ }; static int pxb_open(dev_t *devp, int flags, int otyp, cred_t *credp); static int pxb_close(dev_t dev, int flags, int otyp, cred_t *credp); static int pxb_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *credp, int *rvalp); static int pxb_prop_op(dev_t dev, dev_info_t *dip, ddi_prop_op_t prop_op, int flags, char *name, caddr_t valuep, int *lengthp); static struct cb_ops pxb_cb_ops = { pxb_open, /* open */ pxb_close, /* close */ nulldev, /* strategy */ nulldev, /* print */ nulldev, /* dump */ nulldev, /* read */ nulldev, /* write */ pxb_ioctl, /* ioctl */ nodev, /* devmap */ nodev, /* mmap */ nodev, /* segmap */ nochpoll, /* poll */ pxb_prop_op, /* cb_prop_op */ NULL, /* streamtab */ D_NEW | D_MP | D_HOTPLUG, /* Driver compatibility flag */ CB_REV, /* rev */ nodev, /* int (*cb_aread)() */ nodev /* int (*cb_awrite)() */ }; static int pxb_probe(dev_info_t *); static int pxb_attach(dev_info_t *devi, ddi_attach_cmd_t cmd); static int pxb_detach(dev_info_t *devi, ddi_detach_cmd_t cmd); static int pxb_info(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, void **result); static int pxb_pwr_setup(dev_info_t *dip); static int pxb_pwr_init_and_raise(dev_info_t *dip, pcie_pwr_t *pwr_p); static void pxb_pwr_teardown(dev_info_t *dip); struct dev_ops pxb_ops = { DEVO_REV, /* devo_rev */ 0, /* refcnt */ pxb_info, /* info */ nulldev, /* identify */ pxb_probe, /* probe */ pxb_attach, /* attach */ pxb_detach, /* detach */ nulldev, /* reset */ &pxb_cb_ops, /* driver operations */ &pxb_bus_ops, /* bus operations */ pcie_power /* power entry */ }; /* * Module linkage information for the kernel. */ static struct modldrv modldrv = { &mod_driverops, /* Type of module */ "PCIe/PCI nexus driver %I%", &pxb_ops, /* driver ops */ }; static struct modlinkage modlinkage = { MODREV_1, (void *)&modldrv, NULL }; /* * soft state pointer and structure template: */ void *pxb_state; /* * SW workaround for PLX HW bug Flag */ int pxb_tlp_count = 64; /* * forward function declarations: */ static int pxb_intr_init(pxb_devstate_t *pxb, int intr_type); static void pxb_intr_fini(pxb_devstate_t *pxb); static uint_t pxb_intr(caddr_t arg1, caddr_t arg2); static int pxb_get_port_type(dev_info_t *dip, ddi_acc_handle_t config_handle); static void pxb_removechild(dev_info_t *); static int pxb_initchild(dev_info_t *child); static dev_info_t *get_my_childs_dip(dev_info_t *dip, dev_info_t *rdip); static void pxb_init_hotplug(pxb_devstate_t *pxb); static void pxb_create_ranges_prop(dev_info_t *, ddi_acc_handle_t); int _init(void) { int e; if ((e = ddi_soft_state_init(&pxb_state, sizeof (pxb_devstate_t), 1)) == 0 && (e = mod_install(&modlinkage)) != 0) ddi_soft_state_fini(&pxb_state); return (e); } int _fini(void) { int e; if ((e = mod_remove(&modlinkage)) == 0) ddi_soft_state_fini(&pxb_state); return (e); } int _info(struct modinfo *modinfop) { return (mod_info(&modlinkage, modinfop)); } /*ARGSUSED*/ static int pxb_info(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, void **result) { pxb_devstate_t *pxb_p; /* per pxb state pointer */ minor_t minor = getminor((dev_t)arg); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pxb_p = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); switch (infocmd) { default: return (DDI_FAILURE); case DDI_INFO_DEVT2INSTANCE: *result = (void *)(intptr_t)instance; return (DDI_SUCCESS); case DDI_INFO_DEVT2DEVINFO: if (pxb_p == NULL) return (DDI_FAILURE); *result = (void *)pxb_p->pxb_dip; return (DDI_SUCCESS); } } /*ARGSUSED*/ static int pxb_probe(register dev_info_t *devi) { return (DDI_PROBE_SUCCESS); } /*ARGSUSED*/ static int pxb_attach(dev_info_t *devi, ddi_attach_cmd_t cmd) { int instance; pxb_devstate_t *pxb; ddi_acc_handle_t config_handle; int intr_types; instance = ddi_get_instance(devi); switch (cmd) { case DDI_RESUME: DBG(DBG_ATTACH, devi, "DDI_RESUME\n"); /* * Get the soft state structure for the bridge. */ pxb = (pxb_devstate_t *) ddi_get_soft_state(pxb_state, instance); (void) pcie_pwr_resume(devi); DEVI_SET_ATTACHING(devi); if (pxb_fm_init(pxb) != DDI_SUCCESS) cmn_err(CE_WARN, "px_pci: dip0x%p failed pxb_fm_init " "at resume\n", (void *) devi); DEVI_CLR_ATTACHING(devi); return (DDI_SUCCESS); case DDI_ATTACH: DBG(DBG_ATTACH, devi, "DDI_ATTACH\n"); /* Follow through to below the switch statement */ break; default: return (DDI_FAILURE); } /* * Allocate and get soft state structure. */ if (ddi_soft_state_zalloc(pxb_state, instance) != DDI_SUCCESS) { DBG(DBG_ATTACH, devi, "Unable to allocate soft state.\n"); return (DDI_FAILURE); } pxb = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); pxb->pxb_dip = devi; pxb->pxb_soft_state = PXB_SOFT_STATE_CLOSED; /* Create Mutex */ mutex_init(&pxb->pxb_mutex, NULL, MUTEX_DRIVER, NULL); pxb->pxb_init_flags = PXB_INIT_MUTEX; /* Setup and save the config space pointer */ if (pci_config_setup(devi, &config_handle) != DDI_SUCCESS) { DBG(DBG_ATTACH, devi, "Failed in pci_config_setup call\n"); goto fail; } pxb->pxb_config_handle = config_handle; pxb->pxb_init_flags |= PXB_INIT_CONFIG_HANDLE; /* Save the vnedor id and device id */ pxb->pxb_vendor_id = pci_config_get16(config_handle, PCI_CONF_VENID); pxb->pxb_device_id = pci_config_get16(config_handle, PCI_CONF_DEVID); /* * Power management setup. This also makes sure that switch/bridge * is at D0 during attach. */ if (pwr_common_setup(devi) != DDI_SUCCESS) { DBG(DBG_PWR, devi, "pwr_common_setup failed\n"); goto fail; } else if (pxb_pwr_setup(devi) != DDI_SUCCESS) { DBG(DBG_PWR, devi, "pxb_pwr_setup failed \n"); goto fail; } if ((pxb_fm_init(pxb)) != DDI_SUCCESS) { DBG(DBG_ATTACH, devi, "Failed in px_pci_fm_attach\n"); goto fail; } pxb->pxb_init_flags |= PXB_INIT_FM; pxb->pxb_port_type = pxb_get_port_type(devi, config_handle); if ((pxb->pxb_port_type != PX_CAP_REG_DEV_TYPE_UP) && (pxb->pxb_port_type != PX_CAP_REG_DEV_TYPE_DOWN) && (pxb->pxb_port_type != PX_CAP_REG_DEV_TYPE_PCIE2PCI) && (pxb->pxb_port_type != PX_CAP_REG_DEV_TYPE_PCI2PCIE)) { DBG(DBG_ATTACH, devi, "This is not a switch or bridge\n"); goto fail; } /* * Make sure the "device_type" property exists. */ (void) ddi_prop_update_string(DDI_DEV_T_NONE, devi, "device_type", "pciex"); /* * Check whether the "ranges" property is present. * Otherwise create the ranges property by reading * the configuration registers */ if (ddi_prop_exists(DDI_DEV_T_ANY, devi, DDI_PROP_DONTPASS, "ranges") == 0) { pxb_create_ranges_prop(devi, config_handle); } /* * Initialize interrupt handlers. * If both MSI and FIXED are supported, try to attach MSI first. * If MSI fails for any reason, then try FIXED, but only allow one * type to be attached. */ if (ddi_intr_get_supported_types(devi, &intr_types) != DDI_SUCCESS) { DBG(DBG_ATTACH, devi, "ddi_intr_get_supported_types failed\n"); goto fail; } if ((intr_types & DDI_INTR_TYPE_MSI) && pxb_enable_msi) { if (pxb_intr_init(pxb, DDI_INTR_TYPE_MSI) == DDI_SUCCESS) intr_types = DDI_INTR_TYPE_MSI; else DBG(DBG_ATTACH, devi, "Unable to attach MSI handler\n"); } if (intr_types & DDI_INTR_TYPE_FIXED) { if (pxb_intr_init(pxb, DDI_INTR_TYPE_FIXED) != DDI_SUCCESS) { DBG(DBG_ATTACH, devi, "Unable to attach INTx handler\n"); goto fail; } } /* * Initialize hotplug support on this bus. At minimum * (for non hotplug bus) this would create ":devctl" minor * node to support DEVCTL_DEVICE_* and DEVCTL_BUS_* ioctls * to this bus. This all takes place if this nexus has hot-plug * slots and successfully initializes Hot Plug Framework. */ pxb->pxb_hotplug_capable = B_FALSE; pxb_init_hotplug(pxb); if (pxb->pxb_hotplug_capable == B_FALSE) { /* * create minor node for devctl interfaces */ if (ddi_create_minor_node(devi, "devctl", S_IFCHR, PCIHP_AP_MINOR_NUM(instance, PCIHP_DEVCTL_MINOR), DDI_NT_NEXUS, 0) != DDI_SUCCESS) goto fail; } DBG(DBG_ATTACH, devi, "pxb_attach(): this nexus %s hotplug slots\n", pxb->pxb_hotplug_capable == B_TRUE ? "has":"has no"); ddi_report_dev(devi); return (DDI_SUCCESS); fail: (void) pxb_detach(devi, DDI_DETACH); return (DDI_FAILURE); } /*ARGSUSED*/ static int pxb_detach(dev_info_t *devi, ddi_detach_cmd_t cmd) { pxb_devstate_t *pxb; int error = DDI_SUCCESS; switch (cmd) { case DDI_DETACH: /* * And finally free the per-pci soft state after * uninitializing hotplug support for this bus in * opposite order of attach. */ pxb = (pxb_devstate_t *) ddi_get_soft_state(pxb_state, ddi_get_instance(devi)); if (pxb->pxb_hotplug_capable == B_TRUE) if (pcihp_uninit(devi) == DDI_FAILURE) error = DDI_FAILURE; else ddi_remove_minor_node(devi, "devctl"); (void) ddi_prop_remove(DDI_DEV_T_NONE, devi, "device_type"); pxb_intr_fini(pxb); if (pxb->pxb_init_flags & PXB_INIT_FM) pxb_fm_fini(pxb); if (pxb->pxb_init_flags & PXB_INIT_CONFIG_HANDLE) pci_config_teardown(&pxb->pxb_config_handle); pxb_pwr_teardown(devi); pwr_common_teardown(devi); if (pxb->pxb_init_flags & PXB_INIT_MUTEX) mutex_destroy(&pxb->pxb_mutex); ddi_soft_state_free(pxb_state, ddi_get_instance(devi)); return (error); case DDI_SUSPEND: pxb = (pxb_devstate_t *) ddi_get_soft_state(pxb_state, ddi_get_instance(devi)); DEVI_SET_DETACHING(devi); pxb_fm_fini(pxb); DEVI_CLR_DETACHING(devi); error = pcie_pwr_suspend(devi); return (error); } return (DDI_FAILURE); } /*ARGSUSED*/ static int pxb_bus_map(dev_info_t *dip, dev_info_t *rdip, ddi_map_req_t *mp, off_t offset, off_t len, caddr_t *vaddrp) { register dev_info_t *pdip; pdip = (dev_info_t *)DEVI(dip)->devi_parent; return ((DEVI(pdip)->devi_ops->devo_bus_ops->bus_map) (pdip, rdip, mp, offset, len, vaddrp)); } /*ARGSUSED*/ static int pxb_ctlops(dev_info_t *dip, dev_info_t *rdip, ddi_ctl_enum_t ctlop, void *arg, void *result) { pci_regspec_t *drv_regp; int reglen; int rn; int totreg; struct detachspec *ds; struct attachspec *as; switch (ctlop) { case DDI_CTLOPS_REPORTDEV: if (rdip == (dev_info_t *)0) return (DDI_FAILURE); cmn_err(CE_CONT, "?PCI-device: %s@%s, %s%d\n", ddi_node_name(rdip), ddi_get_name_addr(rdip), ddi_driver_name(rdip), ddi_get_instance(rdip)); return (DDI_SUCCESS); case DDI_CTLOPS_INITCHILD: return (pxb_initchild((dev_info_t *)arg)); case DDI_CTLOPS_UNINITCHILD: pxb_removechild((dev_info_t *)arg); return (DDI_SUCCESS); case DDI_CTLOPS_SIDDEV: return (DDI_SUCCESS); case DDI_CTLOPS_REGSIZE: case DDI_CTLOPS_NREGS: if (rdip == (dev_info_t *)0) return (DDI_FAILURE); break; case DDI_CTLOPS_ATTACH: as = (struct attachspec *)arg; switch (as->when) { case DDI_PRE: if (as->cmd == DDI_ATTACH) { DBG(DBG_PWR, dip, "PRE_ATTACH for %s@%d\n", ddi_driver_name(rdip), ddi_get_instance(rdip)); return (pcie_pm_hold(dip)); } if (as->cmd == DDI_RESUME) { ddi_acc_handle_t config_handle; DBG(DBG_PWR, dip, "PRE_RESUME for %s@%d\n", ddi_driver_name(rdip), ddi_get_instance(rdip)); if (pci_config_setup(rdip, &config_handle) == DDI_SUCCESS) { pcie_clear_errors(rdip, config_handle); pci_config_teardown(&config_handle); } } return (DDI_SUCCESS); case DDI_POST: DBG(DBG_PWR, dip, "POST_ATTACH for %s@%d\n", ddi_driver_name(rdip), ddi_get_instance(rdip)); if (as->cmd == DDI_ATTACH && as->result != DDI_SUCCESS) pcie_pm_release(dip); return (DDI_SUCCESS); default: break; } break; case DDI_CTLOPS_DETACH: ds = (struct detachspec *)arg; switch (ds->when) { case DDI_POST: if (ds->cmd == DDI_DETACH && ds->result == DDI_SUCCESS) { DBG(DBG_PWR, dip, "POST_DETACH for %s@%d\n", ddi_driver_name(rdip), ddi_get_instance(rdip)); return (pcie_pm_remove_child(dip, rdip)); } return (DDI_SUCCESS); default: break; } break; default: return (ddi_ctlops(dip, rdip, ctlop, arg, result)); } *(int *)result = 0; if (ddi_getlongprop(DDI_DEV_T_ANY, rdip, DDI_PROP_DONTPASS | DDI_PROP_CANSLEEP, "reg", (caddr_t)&drv_regp, ®len) != DDI_SUCCESS) return (DDI_FAILURE); totreg = reglen / sizeof (pci_regspec_t); if (ctlop == DDI_CTLOPS_NREGS) *(int *)result = totreg; else if (ctlop == DDI_CTLOPS_REGSIZE) { rn = *(int *)arg; if (rn >= totreg) { kmem_free(drv_regp, reglen); return (DDI_FAILURE); } *(off_t *)result = drv_regp[rn].pci_size_low | ((uint64_t)drv_regp[rn].pci_size_hi << 32); } kmem_free(drv_regp, reglen); return (DDI_SUCCESS); } static dev_info_t * get_my_childs_dip(dev_info_t *dip, dev_info_t *rdip) { dev_info_t *cdip = rdip; for (; ddi_get_parent(cdip) != dip; cdip = ddi_get_parent(cdip)) ; return (cdip); } static int pxb_intr_ops(dev_info_t *dip, dev_info_t *rdip, ddi_intr_op_t intr_op, ddi_intr_handle_impl_t *hdlp, void *result) { dev_info_t *cdip = rdip; pci_regspec_t *pci_rp; int reglen, len; uint32_t d, intr; if (hdlp->ih_type != DDI_INTR_TYPE_FIXED) goto done; /* * If the interrupt-map property is defined at this * node, it will have performed the interrupt * translation as part of the property, so no * rotation needs to be done. */ if (ddi_getproplen(DDI_DEV_T_ANY, dip, DDI_PROP_DONTPASS, "interrupt-map", &len) == DDI_PROP_SUCCESS) goto done; cdip = get_my_childs_dip(dip, rdip); /* * Use the devices reg property to determine its * PCI bus number and device number. */ if (ddi_getlongprop(DDI_DEV_T_ANY, cdip, DDI_PROP_DONTPASS, "reg", (caddr_t)&pci_rp, ®len) != DDI_SUCCESS) return (DDI_FAILURE); intr = hdlp->ih_vector; /* spin the interrupt */ d = PCI_REG_DEV_G(pci_rp[0].pci_phys_hi); if ((intr >= PCI_INTA) && (intr <= PCI_INTD)) hdlp->ih_vector = ((intr - 1 + (d % 4)) % 4 + 1); else cmn_err(CE_WARN, "%s%d: %s: PCI intr=%x out of range", ddi_driver_name(rdip), ddi_get_instance(rdip), ddi_driver_name(dip), intr); kmem_free(pci_rp, reglen); done: /* Pass up the request to our parent. */ return (i_ddi_intr_ops(dip, rdip, intr_op, hdlp, result)); } /* * name_child * * This function is called from init_child to name a node. It is * also passed as a callback for node merging functions. * * return value: DDI_SUCCESS, DDI_FAILURE */ static int pxb_name_child(dev_info_t *child, char *name, int namelen) { pci_regspec_t *pci_rp; uint_t slot, func; char **unit_addr; uint_t n; /* * Pseudo nodes indicate a prototype node with per-instance * properties to be merged into the real h/w device node. * The interpretation of the unit-address is DD[,F] * where DD is the device id and F is the function. */ if (ndi_dev_is_persistent_node(child) == 0) { if (ddi_prop_lookup_string_array(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "unit-address", &unit_addr, &n) != DDI_PROP_SUCCESS) { cmn_err(CE_WARN, "cannot name node from %s.conf", ddi_driver_name(child)); return (DDI_FAILURE); } if (n != 1 || *unit_addr == NULL || **unit_addr == 0) { cmn_err(CE_WARN, "unit-address property in %s.conf" " not well-formed", ddi_driver_name(child)); ddi_prop_free(unit_addr); return (DDI_FAILURE); } (void) snprintf(name, namelen, "%s", *unit_addr); ddi_prop_free(unit_addr); return (DDI_SUCCESS); } /* * Get the address portion of the node name based on * the function and device number. */ if (ddi_prop_lookup_int_array(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "reg", (int **)&pci_rp, &n) != DDI_SUCCESS) { return (DDI_FAILURE); } slot = PCI_REG_DEV_G(pci_rp[0].pci_phys_hi); func = PCI_REG_FUNC_G(pci_rp[0].pci_phys_hi); if (func != 0) (void) snprintf(name, namelen, "%x,%x", slot, func); else (void) snprintf(name, namelen, "%x", slot); ddi_prop_free(pci_rp); return (DDI_SUCCESS); } static int pxb_initchild(dev_info_t *child) { ddi_acc_handle_t config_handle; char name[MAXNAMELEN]; pxb_devstate_t *pxb; int result = DDI_FAILURE; int i; uint16_t reg = 0; /* * Name the child */ if (pxb_name_child(child, name, MAXNAMELEN) != DDI_SUCCESS) { result = DDI_FAILURE; goto done; } ddi_set_name_addr(child, name); ddi_set_parent_data(child, NULL); /* * Pseudo nodes indicate a prototype node with per-instance * properties to be merged into the real h/w device node. * The interpretation of the unit-address is DD[,F] * where DD is the device id and F is the function. */ if (ndi_dev_is_persistent_node(child) == 0) { extern int pci_allow_pseudo_children; /* * Try to merge the properties from this prototype * node into real h/w nodes. */ if (ndi_merge_node(child, pxb_name_child) == DDI_SUCCESS) { /* * Merged ok - return failure to remove the node. */ pxb_removechild(child); result = DDI_FAILURE; goto done; } /* workaround for ddivs to run under PCI */ if (pci_allow_pseudo_children) { result = DDI_SUCCESS; goto done; } /* * The child was not merged into a h/w node, * but there's not much we can do with it other * than return failure to cause the node to be removed. */ cmn_err(CE_WARN, "!%s@%s: %s.conf properties not merged", ddi_driver_name(child), ddi_get_name_addr(child), ddi_driver_name(child)); pxb_removechild(child); result = DDI_NOT_WELL_FORMED; goto done; } ddi_set_parent_data(child, NULL); pxb = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, ddi_get_instance(ddi_get_parent(child))); if (pcie_pm_hold(pxb->pxb_dip) != DDI_SUCCESS) { DBG(DBG_PWR, pxb->pxb_dip, "INITCHILD: px_pm_hold failed\n"); result = DDI_FAILURE; goto done; } /* Any return from here must call pcie_pm_release */ /* * If configuration registers were previously saved by * child (before it entered D3), then let the child do the * restore to set up the config regs as it'll first need to * power the device out of D3. */ if (ddi_prop_exists(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "config-regs-saved-by-child") == 1) { DBG(DBG_PWR, ddi_get_parent(child), "INITCHILD: config regs to be restored by child" " for %s@%s\n", ddi_node_name(child), ddi_get_name_addr(child)); result = DDI_SUCCESS; goto cleanup; } DBG(DBG_PWR, ddi_get_parent(child), "INITCHILD: config regs setup for %s@%s\n", ddi_node_name(child), ddi_get_name_addr(child)); if (pcie_initchild(child) != DDI_SUCCESS) { result = DDI_FAILURE; goto cleanup; } /* * Due to a PLX HW bug, a SW workaround to prevent the chip from * wedging is needed. SW just needs to tranfer 64 TLPs from * the downstream port to the child device. * The most benign way of doing this is to read the ID register * 64 times. This SW workaround should have minimum performance * impact and shouldn't cause a problem for all other bridges * and switches. * * The code needs to be written in a way to make sure it isn't * optimized out. */ if ((!pxb_tlp_count) || (pxb->pxb_vendor_id != PXB_VENDOR_PLX) || ((pxb->pxb_device_id != PXB_DEVICE_PLX_8532) && (pxb->pxb_device_id != PXB_DEVICE_PLX_8516))) { /* Workaround not needed return success */ result = DDI_SUCCESS; goto cleanup; } if (pci_config_setup(child, &config_handle) != DDI_SUCCESS) { result = DDI_FAILURE; goto cleanup; } for (i = 0; i < pxb_tlp_count; i += 1) reg |= pci_config_get16(config_handle, PCI_CONF_VENID); pci_config_teardown(&config_handle); result = DDI_SUCCESS; cleanup: pcie_pm_release(pxb->pxb_dip); done: return (result); } /* * This function initializes internally generated interrupts only. * It does not affect any interrupts generated by downstream devices * or the forwarding of them. * * Enable Device Specific Interrupts or Hotplug features here. * Enabling features may change how many interrupts are requested * by the device. If features are not enabled first, the * device might not ask for any interrupts. */ static int pxb_intr_init(pxb_devstate_t *pxb, int intr_type) { dev_info_t *dip = pxb->pxb_dip; int request, count, x; int ret; int intr_cap = 0; DBG(DBG_ATTACH, dip, "Attaching %s handler\n", (intr_type == DDI_INTR_TYPE_MSI) ? "MSI" : "INTx"); /* * Get number of requested interrupts. If none requested or DDI_FAILURE * just return DDI_SUCCESS. * * Several Bridges/Switches will not have this property set, resulting * in a FAILURE, if the device is not configured in a way that * interrupts are needed. (eg. hotplugging) */ ret = ddi_intr_get_nintrs(dip, intr_type, &request); if (ret != DDI_SUCCESS || request == 0) { DBG(DBG_ATTACH, dip, "ddi_intr_get_nintrs() ret: %d req %d\n", ret, request); return (DDI_SUCCESS); } /* Find out how many MSI's are available. */ if (intr_type == DDI_INTR_TYPE_MSI) { ret = ddi_intr_get_navail(dip, intr_type, &count); if ((ret != DDI_SUCCESS) || (count == 0)) { DBG(DBG_ATTACH, dip, "ddi_intr_get_navail() ret: %d available: %d\n", ret, count); goto fail; } if (request < count) { DBG(DBG_ATTACH, dip, "Requested Intr: %d Available: %d\n", request, count); request = count; } } /* Allocate an array of interrupt handlers */ pxb->pxb_htable_size = sizeof (ddi_intr_handle_t) * request; pxb->pxb_htable = kmem_zalloc(pxb->pxb_htable_size, KM_SLEEP); pxb->pxb_init_flags |= PXB_INIT_HTABLE; ret = ddi_intr_alloc(dip, pxb->pxb_htable, intr_type, 0, request, &count, DDI_INTR_ALLOC_NORMAL); if ((ret != DDI_SUCCESS) || (count == 0)) { DBG(DBG_ATTACH, dip, "ddi_intr_alloc() ret: %d ask: %d actual: %d\n", ret, request, count); goto fail; } /* Save the actually number of interrupts allocated */ pxb->pxb_intr_count = count; if (count < request) { DBG(DBG_ATTACH, dip, "Requested Intr: %d Received: %d\n", request, count); } pxb->pxb_init_flags |= PXB_INIT_ALLOC; /* Get interrupt priority */ ret = ddi_intr_get_pri(pxb->pxb_htable[0], &pxb->pxb_intr_priority); if (ret != DDI_SUCCESS) { DBG(DBG_ATTACH, dip, "ddi_intr_get_pri() ret: %d\n", ret); goto fail; } if (pxb->pxb_intr_priority >= LOCK_LEVEL) { pxb->pxb_intr_priority = LOCK_LEVEL - 1; ret = ddi_intr_set_pri(pxb->pxb_htable[0], pxb->pxb_intr_priority); if (ret != DDI_SUCCESS) { DBG(DBG_ATTACH, dip, "ddi_intr_set_pri() ret: %d\n", ret); goto fail; } } for (count = 0; count < pxb->pxb_intr_count; count++) { ret = ddi_intr_add_handler(pxb->pxb_htable[count], pxb_intr, (caddr_t)pxb, NULL); if (ret != DDI_SUCCESS) { DBG(DBG_ATTACH, dip, "ddi_intr_add_handler() ret: %d\n", ret); break; } } /* If unsucessful remove the added handlers */ if (ret != DDI_SUCCESS) { for (x = 0; x < count; x++) { (void) ddi_intr_remove_handler(pxb->pxb_htable[x]); } goto fail; } pxb->pxb_init_flags |= PXB_INIT_HANDLER; (void) ddi_intr_get_cap(pxb->pxb_htable[0], &intr_cap); if (intr_cap & DDI_INTR_FLAG_BLOCK) { (void) ddi_intr_block_enable(pxb->pxb_htable, pxb->pxb_intr_count); pxb->pxb_init_flags |= PXB_INIT_BLOCK; } else { for (count = 0; count < pxb->pxb_intr_count; count++) { (void) ddi_intr_enable(pxb->pxb_htable[count]); } } pxb->pxb_init_flags |= PXB_INIT_ENABLE; /* Save the interrupt type */ pxb->pxb_intr_type = intr_type; return (DDI_SUCCESS); fail: pxb_intr_fini(pxb); return (DDI_FAILURE); } static void pxb_intr_fini(pxb_devstate_t *pxb) { int x; int count = pxb->pxb_intr_count; int flags = pxb->pxb_init_flags; if ((flags & PXB_INIT_ENABLE) && (flags & PXB_INIT_BLOCK)) { (void) ddi_intr_block_disable(pxb->pxb_htable, count); flags &= ~(PXB_INIT_ENABLE | PXB_INIT_BLOCK); } for (x = 0; x < count; x++) { if (flags & PXB_INIT_ENABLE) (void) ddi_intr_disable(pxb->pxb_htable[x]); if (flags & PXB_INIT_HANDLER) (void) ddi_intr_remove_handler(pxb->pxb_htable[x]); if (flags & PXB_INIT_ALLOC) (void) ddi_intr_free(pxb->pxb_htable[x]); } flags &= ~(PXB_INIT_ENABLE | PXB_INIT_HANDLER | PXB_INIT_ALLOC); if (flags & PXB_INIT_HTABLE) kmem_free(pxb->pxb_htable, pxb->pxb_htable_size); flags &= ~PXB_INIT_HTABLE; pxb->pxb_init_flags &= flags; } /* * This only handles internal errors, not bus errors. * Currently the only known interrupt would be from hotplugging. */ /*ARGSUSED*/ static uint_t pxb_intr(caddr_t arg1, caddr_t arg2) { pxb_devstate_t *pxb = (pxb_devstate_t *)arg1; dev_info_t *dip = pxb->pxb_dip; cmn_err(CE_WARN, "%s%d: Received %s Interrupt\n", ddi_driver_name(dip), ddi_get_instance(dip), (pxb->pxb_intr_type == DDI_INTR_TYPE_MSI) ? "MSI" : "INTx"); return (DDI_INTR_UNCLAIMED); } static int pxb_get_port_type(dev_info_t *dip, ddi_acc_handle_t config_handle) { ushort_t caps_ptr, cap; int port_type = PX_CAP_REG_DEV_TYPE_PCIE_DEV; /* * Check if capabilities list is supported. If not then it is a PCI * device. If so, check to see if it contains PCI Express Capability * Register. Eventually move this code to PCI-EX Framework. */ if (pci_config_get16(config_handle, PCI_CONF_STAT) & PCI_STAT_CAP) caps_ptr = P2ALIGN(pci_config_get8(config_handle, PCI_CONF_CAP_PTR), 4); else caps_ptr = PCI_CAP_NEXT_PTR_NULL; while (caps_ptr != PCI_CAP_NEXT_PTR_NULL) { if (caps_ptr < 0x40) { DBG(DBG_ATTACH, dip, "Capability pointer 0x%x out of range.\n", caps_ptr); break; } cap = pci_config_get8(config_handle, caps_ptr); if (cap == PCI_CAP_ID_PCI_E) { port_type = pci_config_get16(config_handle, caps_ptr + PX_CAP_REG) & PX_CAP_REG_DEV_TYPE_MASK; break; } caps_ptr = P2ALIGN(pci_config_get8(config_handle, (caps_ptr + PCI_CAP_NEXT_PTR)), 4); } return (port_type); } static void pxb_removechild(dev_info_t *dip) { ddi_set_name_addr(dip, NULL); /* * Strip the node to properly convert it back to prototype form */ ddi_remove_minor_node(dip, NULL); impl_rem_dev_props(dip); pcie_uninitchild(dip); } /* * Initialize hotplug framework if we are hotpluggable. * Sets flag in the soft state if Hot Plug is supported and initialized * properly. */ /*ARGSUSED*/ static void pxb_init_hotplug(pxb_devstate_t *pxb) { /* * Hot plug support to be decided. */ } static void pxb_create_ranges_prop(dev_info_t *dip, ddi_acc_handle_t config_handle) { uint32_t base, limit; pxb_ranges_t ranges[PXB_RANGE_LEN]; uint8_t io_base_lo, io_limit_lo; uint16_t io_base_hi, io_limit_hi, mem_base, mem_limit; int i = 0, rangelen = sizeof (pxb_ranges_t)/sizeof (int); io_base_lo = pci_config_get8(config_handle, PCI_BCNF_IO_BASE_LOW); io_limit_lo = pci_config_get8(config_handle, PCI_BCNF_IO_LIMIT_LOW); io_base_hi = pci_config_get16(config_handle, PCI_BCNF_IO_BASE_HI); io_limit_hi = pci_config_get16(config_handle, PCI_BCNF_IO_LIMIT_HI); mem_base = pci_config_get16(config_handle, PCI_BCNF_MEM_BASE); mem_limit = pci_config_get16(config_handle, PCI_BCNF_MEM_LIMIT); /* * Create ranges for IO space */ ranges[i].size_low = ranges[i].size_high = 0; ranges[i].parent_mid = ranges[i].child_mid = ranges[i].parent_high = 0; ranges[i].child_high = ranges[i].parent_high |= (PCI_REG_REL_M | PCI_ADDR_IO); base = PXB_16bit_IOADDR(io_base_lo); limit = PXB_16bit_IOADDR(io_limit_lo); if ((io_base_lo & 0xf) == PXB_32BIT_IO) { base = PXB_LADDR(base, io_base_hi); } if ((io_limit_lo & 0xf) == PXB_32BIT_IO) { limit = PXB_LADDR(limit, io_limit_hi); } if ((io_base_lo & PXB_32BIT_IO) && (io_limit_hi > 0)) { base = PXB_LADDR(base, io_base_hi); limit = PXB_LADDR(limit, io_limit_hi); } /* * Create ranges for 32bit memory space */ base = PXB_32bit_MEMADDR(mem_base); limit = PXB_32bit_MEMADDR(mem_limit); ranges[i].size_low = ranges[i].size_high = 0; ranges[i].parent_mid = ranges[i].child_mid = ranges[i].parent_high = 0; ranges[i].child_high = ranges[i].parent_high |= (PCI_REG_REL_M | PCI_ADDR_MEM32); ranges[i].child_low = ranges[i].parent_low = base; if (limit >= base) { ranges[i].size_low = limit - base + PXB_MEMGRAIN; i++; } if (i) { (void) ndi_prop_update_int_array(DDI_DEV_T_NONE, dip, "ranges", (int *)ranges, i * rangelen); } } /*ARGSUSED*/ static int pxb_open(dev_t *devp, int flags, int otyp, cred_t *credp) { pxb_devstate_t *pxb_p; minor_t minor = getminor(*devp); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); /* * Make sure the open is for the right file type. */ if (otyp != OTYP_CHR) return (EINVAL); /* * Get the soft state structure for the device. */ pxb_p = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); if (pxb_p == NULL) return (ENXIO); if (pxb_p->pxb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_open(devp, flags, otyp, credp)); /* * Handle the open by tracking the device state. */ mutex_enter(&pxb_p->pxb_mutex); if (flags & FEXCL) { if (pxb_p->pxb_soft_state != PXB_SOFT_STATE_CLOSED) { mutex_exit(&pxb_p->pxb_mutex); return (EBUSY); } pxb_p->pxb_soft_state = PXB_SOFT_STATE_OPEN_EXCL; } else { if (pxb_p->pxb_soft_state == PXB_SOFT_STATE_OPEN_EXCL) { mutex_exit(&pxb_p->pxb_mutex); return (EBUSY); } pxb_p->pxb_soft_state = PXB_SOFT_STATE_OPEN; } mutex_exit(&pxb_p->pxb_mutex); return (0); } /*ARGSUSED*/ static int pxb_close(dev_t dev, int flags, int otyp, cred_t *credp) { pxb_devstate_t *pxb_p; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); if (otyp != OTYP_CHR) return (EINVAL); pxb_p = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); if (pxb_p == NULL) return (ENXIO); if (pxb_p->pxb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_close(dev, flags, otyp, credp)); mutex_enter(&pxb_p->pxb_mutex); pxb_p->pxb_soft_state = PXB_SOFT_STATE_CLOSED; mutex_exit(&pxb_p->pxb_mutex); return (0); } /* * pxb_ioctl: devctl hotplug controls */ /*ARGSUSED*/ static int pxb_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *credp, int *rvalp) { pxb_devstate_t *pxb_p; dev_info_t *self; struct devctl_iocdata *dcp; uint_t bus_state; int rv = 0; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pxb_p = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); if (pxb_p == NULL) return (ENXIO); if (pxb_p->pxb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_ioctl(dev, cmd, arg, mode, credp, rvalp)); self = pxb_p->pxb_dip; /* * We can use the generic implementation for these ioctls */ switch (cmd) { case DEVCTL_DEVICE_GETSTATE: case DEVCTL_DEVICE_ONLINE: case DEVCTL_DEVICE_OFFLINE: case DEVCTL_BUS_GETSTATE: return (ndi_devctl_ioctl(self, cmd, arg, mode, 0)); } /* * read devctl ioctl data */ if (ndi_dc_allochdl((void *)arg, &dcp) != NDI_SUCCESS) return (EFAULT); switch (cmd) { case DEVCTL_DEVICE_RESET: rv = ENOTSUP; break; case DEVCTL_BUS_QUIESCE: if (ndi_get_bus_state(self, &bus_state) == NDI_SUCCESS) if (bus_state == BUS_QUIESCED) break; (void) ndi_set_bus_state(self, BUS_QUIESCED); break; case DEVCTL_BUS_UNQUIESCE: if (ndi_get_bus_state(self, &bus_state) == NDI_SUCCESS) if (bus_state == BUS_ACTIVE) break; (void) ndi_set_bus_state(self, BUS_ACTIVE); break; case DEVCTL_BUS_RESET: rv = ENOTSUP; break; case DEVCTL_BUS_RESETALL: rv = ENOTSUP; break; default: rv = ENOTTY; } ndi_dc_freehdl(dcp); return (rv); } static int pxb_prop_op(dev_t dev, dev_info_t *dip, ddi_prop_op_t prop_op, int flags, char *name, caddr_t valuep, int *lengthp) { pxb_devstate_t *pxb_p; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pxb_p = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); if (pxb_p == NULL) return (ENXIO); if (pxb_p->pxb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_prop_op(dev, dip, prop_op, flags, name, valuep, lengthp)); return (ddi_prop_op(dev, dip, prop_op, flags, name, valuep, lengthp)); } /* * Power management related initialization specific to px_pci. * Called by pxb_attach() */ static int pxb_pwr_setup(dev_info_t *dip) { char *comp_array[5]; int i, instance; ddi_acc_handle_t conf_hdl; uint8_t cap_ptr, cap_id; uint16_t pmcap; pcie_pwr_t *pwr_p; pxb_devstate_t *pxb; ASSERT(PCIE_PMINFO(dip)); pwr_p = PCIE_NEXUS_PMINFO(dip); ASSERT(pwr_p); instance = ddi_get_instance(dip); pxb = (pxb_devstate_t *)ddi_get_soft_state(pxb_state, instance); /* * Disable PM for PLX 8532 switch. Transitioning one port on * this switch to low power causes links on other ports on the * same station to die. * Due to PLX erratum #34, we can't allow the downstream device * go to non-D0 state. */ if ((pxb->pxb_vendor_id == PXB_VENDOR_PLX) && ((pxb->pxb_device_id == PXB_DEVICE_PLX_8516) || (pxb->pxb_device_id == PXB_DEVICE_PLX_8532))) { DBG(DBG_PWR, dip, "pxb_pwr_setup: PLX8532/PLX8516 found " "disabling PM\n"); pwr_p->pwr_func_lvl = PM_LEVEL_D0; pwr_p->pwr_flags = PCIE_NO_CHILD_PM; return (DDI_SUCCESS); } /* Code taken from pci_pci driver */ if (pci_config_setup(dip, &pwr_p->pwr_conf_hdl) != DDI_SUCCESS) { DBG(DBG_PWR, dip, "pxb_pwr_setup: pci_config_setup failed\n"); return (DDI_FAILURE); } conf_hdl = pwr_p->pwr_conf_hdl; cap_ptr = pci_config_get8(conf_hdl, PCI_BCNF_CAP_PTR); /* * Walk the capabilities searching for a PM entry. */ while (cap_ptr != PCI_CAP_NEXT_PTR_NULL) { cap_id = pci_config_get8(conf_hdl, cap_ptr + PCI_CAP_ID); if (cap_id == PCI_CAP_ID_PM) { break; } cap_ptr = pci_config_get8(conf_hdl, cap_ptr + PCI_CAP_NEXT_PTR); } if (cap_ptr == 0) { DBG(DBG_PWR, dip, "switch/bridge does not support PM. PCI" " PM data structure not found in config header\n"); pci_config_teardown(&conf_hdl); return (DDI_SUCCESS); } /* * Save offset to pmcsr for future references. */ pwr_p->pwr_pmcsr_offset = cap_ptr + PCI_PMCSR; pmcap = pci_config_get16(conf_hdl, cap_ptr + PCI_PMCAP); if (pmcap & PCI_PMCAP_D1) { DBG(DBG_PWR, dip, "D1 state supported\n"); pwr_p->pwr_pmcaps |= PCIE_SUPPORTS_D1; } if (pmcap & PCI_PMCAP_D2) { DBG(DBG_PWR, dip, "D2 state supported\n"); pwr_p->pwr_pmcaps |= PCIE_SUPPORTS_D2; } i = 0; comp_array[i++] = "NAME=PCIe switch/bridge PM"; comp_array[i++] = "0=Power Off (D3)"; if (pwr_p->pwr_pmcaps & PCIE_SUPPORTS_D2) comp_array[i++] = "1=D2"; if (pwr_p->pwr_pmcaps & PCIE_SUPPORTS_D1) comp_array[i++] = "2=D1"; comp_array[i++] = "3=Full Power D0"; /* * Create pm-components property, if it does not exist already. */ if (ddi_prop_update_string_array(DDI_DEV_T_NONE, dip, "pm-components", comp_array, i) != DDI_PROP_SUCCESS) { DBG(DBG_PWR, dip, "could not create pm-components prop\n"); pci_config_teardown(&conf_hdl); return (DDI_FAILURE); } return (pxb_pwr_init_and_raise(dip, pwr_p)); } /* * Initializes the power level and raise the power to D0, if it is * not at D0. */ static int pxb_pwr_init_and_raise(dev_info_t *dip, pcie_pwr_t *pwr_p) { uint16_t pmcsr; int ret = DDI_SUCCESS; /* * Intialize our power level from PMCSR. The common code initializes * this to UNKNOWN. There is no guarantee that we will be at full * power at attach. If we are not at D0, raise the power. */ pmcsr = pci_config_get16(pwr_p->pwr_conf_hdl, pwr_p->pwr_pmcsr_offset); pmcsr &= PCI_PMCSR_STATE_MASK; switch (pmcsr) { case PCI_PMCSR_D0: pwr_p->pwr_func_lvl = PM_LEVEL_D0; break; case PCI_PMCSR_D1: pwr_p->pwr_func_lvl = PM_LEVEL_D1; break; case PCI_PMCSR_D2: pwr_p->pwr_func_lvl = PM_LEVEL_D2; break; case PCI_PMCSR_D3HOT: pwr_p->pwr_func_lvl = PM_LEVEL_D3; break; default: break; } /* Raise the power to D0. */ if (pwr_p->pwr_func_lvl != PM_LEVEL_D0 && ((ret = pm_raise_power(dip, 0, PM_LEVEL_D0)) != DDI_SUCCESS)) { /* * Read PMCSR again. If it is at D0, ignore the return * value from pm_raise_power. */ pmcsr = pci_config_get16(pwr_p->pwr_conf_hdl, pwr_p->pwr_pmcsr_offset); if ((pmcsr & PCI_PMCSR_STATE_MASK) == PCI_PMCSR_D0) ret = DDI_SUCCESS; else { DBG(DBG_PWR, dip, "pxb_pwr_setup: could not raise " "power to D0 \n"); } } if (ret == DDI_SUCCESS) pwr_p->pwr_func_lvl = PM_LEVEL_D0; return (ret); } static int pxb_fm_init(pxb_devstate_t *pxb_p) { ddi_fm_error_t derr; dev_info_t *dip = pxb_p->pxb_dip; pxb_p->pxb_fm_cap = DDI_FM_EREPORT_CAPABLE | DDI_FM_ERRCB_CAPABLE | DDI_FM_ACCCHK_CAPABLE; /* * Request our capability level and get our parents capability * and ibc. */ ddi_fm_init(dip, &pxb_p->pxb_fm_cap, &pxb_p->pxb_fm_ibc); pci_ereport_setup(dip); /* * clear any outstanding error bits */ bzero(&derr, sizeof (ddi_fm_error_t)); derr.fme_version = DDI_FME_VERSION; derr.fme_flag = DDI_FM_ERR_EXPECTED; pci_ereport_post(dip, &derr, NULL); pci_bdg_ereport_post(dip, &derr, NULL); /* * Register error callback with our parent. */ ddi_fm_handler_register(pxb_p->pxb_dip, pxb_fm_err_callback, NULL); return (DDI_SUCCESS); } /* * Breakdown our FMA resources */ static void pxb_fm_fini(pxb_devstate_t *pxb_p) { dev_info_t *dip = pxb_p->pxb_dip; /* * Clean up allocated fm structures */ ddi_fm_handler_unregister(dip); pci_ereport_teardown(dip); ddi_fm_fini(dip); } /* * Function used to initialize FMA for our children nodes. Called * through pci busops when child node calls ddi_fm_init. */ /*ARGSUSED*/ int pxb_fm_init_child(dev_info_t *dip, dev_info_t *cdip, int cap, ddi_iblock_cookie_t *ibc_p) { pxb_devstate_t *pxb_p = (pxb_devstate_t *) ddi_get_soft_state(pxb_state, ddi_get_instance(dip)); *ibc_p = pxb_p->pxb_fm_ibc; return (pxb_p->pxb_fm_cap | DDI_FM_DMACHK_CAPABLE); } /* * Error callback handler. */ /*ARGSUSED*/ static int pxb_fm_err_callback(dev_info_t *dip, ddi_fm_error_t *derr, const void *impl_data) { /* Need to revisit when pcie fm is supported */ uint16_t pci_cfg_stat, pci_cfg_sec_stat; pci_ereport_post(dip, derr, &pci_cfg_stat); pci_bdg_ereport_post(dip, derr, &pci_cfg_sec_stat); return (pci_bdg_check_status(dip, derr, pci_cfg_stat, pci_cfg_sec_stat)); } /* * undo whatever is done in pxb_pwr_setup. called by pxb_detach() */ static void pxb_pwr_teardown(dev_info_t *dip) { pcie_pwr_t *pwr_p; if (!PCIE_PMINFO(dip) || !(pwr_p = PCIE_NEXUS_PMINFO(dip))) return; (void) ddi_prop_remove(DDI_DEV_T_NONE, dip, "pm-components"); if (pwr_p->pwr_conf_hdl) pci_config_teardown(&pwr_p->pwr_conf_hdl); }