Updated grig to version 0.7.2:

GRIG 0.7.2:

- Fixed bug that caused wrong handling of RF gain, IF shift, MIC gain,
  and compressor controls (bug #1613622).
- Give volume level control higher priority to avoid jumpy behaviour
  (bug #1616926).


GRIG 0.7.1:

- A bug that caused installation to fail has been fixed (#1523367).


GRIG 0.7.0:

- Added receiver and transmitter level controls.
- Fixed bug that caused installation errors when using autoconf 2.59e.
- Pixmaps are now installed to /usr/local/share/pixmaps/grig instead of
  /usr/local/share/grig/pixmaps by default (related to the above bug).


GRIG 0.6.0:

- Save and restore RIG state.
- RF power meter scale is now functional with ranges of 5, 10, 50, 100
  and 500 watts. There is currently a bug, which causes the meter needle
  to jump up when switching between RX/TX.
- Fixed bug, which caused the frequency reading to flicker between the
  current value and a previously set value (bug #1388342). Same bug was
  found for the PTT and POWER controls, too.
- Fixed bug, which gave the error message "Can not find VFO list for this
  rig! Bug in backend?" if the rig did not have any of the rig_set_vfo or
  rig_get_vfo functions (bug #1440876).
- Better error messages when a command fails to execute.
- Fixed bug, which blocked the debug handler to properly filter messages
  coming from grig (hamlib messages were filtered correctly).


GRIG 0.5.0:

- Requires Gtk+ 2.6 and Hamlib 1.2.5
- Added VFO and SPLIT controls.
- Special rig functions: LOCK, ...
- Use own debug handler for both hamlib and grig messages
  and format debug messages so that become easier to analyse.
- New debug message window, which can be used to analyse
  previously saved debug messages.
- Modified shutdown procedure to wait until daemon actually
  finishes instead of using a fixed length timeout.
- Disable POWER and PTT buttons by default (can be enabled
  via the command line).
- Optimisation of the daemon process allowing faster reaction
  when PTT is toggled.
- The mode selector combo only shows modes, which are supported
  by the rig.
- Fixed erroneous detection of set/get level availability
  (bug #1266068).
- Fixed incorrect handling of empty ATT, PREAMP and tuning
  step lists in the Radio Info window (bug #1266071).
- Fixed a bug, which caused grig to display WIDE instead of
  NORMAL passband when the rig has no wide passband.
- Optimised S-meter dynamics.
- Better detection of frequency ranges and resolutions.
- Corrected various mistakes in the manual page.
- Various minor improvements to the user interface.
- Several minor changes to support wintendo builds.

1 files changed, 2 insertions, 1 deletions

diff --git a/doc/CHANGES-2006 b/doc/CHANGES-2006
index 3800373760a..713154ea747 100644
--- a/doc/CHANGES-2006
+++ b/doc/CHANGES-2006
@@ -1,4 +1,4 @@
-$NetBSD: CHANGES-2006,v 1.2056 2006/12/27 04:13:02 wulf Exp $
+$NetBSD: CHANGES-2006,v 1.2057 2006/12/27 05:59:04 wulf Exp $
 
 Changes to the packages collection and infrastructure in 2006:
 
@@ -5703,3 +5703,4 @@ Changes to the packages collection and infrastructure in 2006:
 	Updated multimedia/xanim to 2.92.0nb2 [wiz 2006-12-23]
 	Updated meta-pkgs/netbsd-www to 1.4nb3 [jnemeth 2006-12-24]
 	Updated ham/hamlib to 1.2.6 [wulf 2006-12-27]
+	Updated ham/grig to 0.7.2 [wulf 2006-12-27]