| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
----------------------------
Version 6.3:
* Major changes compared to the previous version:
- Backout of
patch #8380: adds 500k 1M 2M baud to ser_posix.c
It broke the functionality in too many situations
(bug #46610/46483)
* New devices supported:
- ATmega48PB, ATmega88PB, ATmega168PB
- ATtiny28 (HVPP-only device)
* New programmers supported:
- Atmel mEDBG: xplainedmini, xplainedmini_dw
* Bugfixes
- bug #46610: Floating point exception (core dumped) arch linux rpi2
- bug #46483: version 6.2. ser_open(): can't set attributes for device
- patch #8435: Implementing mEDBG CMSIS-DAP protocol
- patch #8735: ATtiny28 support in avrdude.conf
- patch #8896: Silence cppcheck warnings in 6.2 code
- patch #8895: Spelling in 6.2 code
Version 6.2:
* Major changes compared to the previous version:
- The stk500v2 implementation now uses its own higher-level
command implementation for byte-wide access, rather than the
historic SPI_MULTI command where all the low-level ISP
implementation had to be assembled manually inside AVRDUDE. In
addition to the traditional STK500, this implementation is also
used by all the more modern Atmel tools (AVRISPmkII, JTAGICEmkII
in ISP mode, STK600 in ISP mode).
- The -B option can be suffixed with "Hz", "kHz", or "MHz", in
order to specify a bitclock frequency rather than period.
- Print part id after signature (patch #8440 )
- buspirate: Also support "cpufreq" extended parameter
in binary mode (patch #8504 )
- The "-P net:" syntax (forwarding of serial data over TCP) is now
also implemented for Win32 systems.
- Allow for arbitrary serial baudrates under Linux (OSX and *BSD
could already handle it).
* New devices supported:
- AT90PWM216 (bug #42310: New part description for AT90PWM216)
- ATmega32M1 (patch #7694 Add support for the atmega32m1)
* New programmers supported:
- ftdi_syncbb
+ uncompatino, ttl232r (FTDI TTL232R-5V with ICSP adapter)
(patch #8529 2 more ftdi_syncbb devices)
* Bugfixes
- bug #45727: Wrong atmega8u2 flash parameters
- bug #46020: Add TIAO TUMPA to the conf file.
- bug #46021: Please add read in the memory lock section of ATtiny85
- bug #42337 avrdude.conf updates for UM232H/CM232H
- bug #42056: double free or corruption triggered at exit
- bug #42158: Linux GPIO - Source Typo
- bug #42516 spelling-error-in-binary
- patch #8419 fix ftdi_syncbb hang with libftdi 1
- bug #43002 usbasp debug output typo
- patch #8511 Fix reset on FT245R
- bug #40142 Floating point exception on Ubuntu 10.04
- bug #22248: Read efuse error (partial fix)
- bug #42267: jtag3isp fails to read lock and fuse bytes directly
after changing lock byte
- bug #41561: AVRDUDE 6.0.1/USBasp doesn't write first bytes of
flash page
- bug #43078: AVRDUDE crashes after sucessfully reading/writing eeprom
- bug #43137: Writing and reading incorrect pages when using jtagicemkI
- bug #40870: config nitpick: ATtiny25/45/85 have 1 calibration byte not 2
- bug #42908: no external reset at JTAGICE3
- patch #8437: [PATCH] Serial-over-ethernet for Win32
- bug #44717: avrdude creates empty flash dump
* Internals:
- Removing exit calls from config parser
- bug #42662 clang warnings under FreeBSD 10.x
|
|
Existing SHA1 digests verified, all found to be the same on the
machine holding the existing distfiles (morden). Existing SHA1
digests retained for now as an audit trail.
|
|
|
|
|
|
----------------------------------------------------------------------
* Major changes compared to the previous version:
- Atmel EDBG protocol support added (JTAGICE3, XplainedPro, Atmel-ICE)
* New programmers supported:
- Atmel DFU, using FLIP protocol version 1 (AT90USB and ATmega*U* devices),
or version 2 (Xmega devices)
- Atmel-ICE (ARM/AVR), JTAG, PDI, debugWIRE, ISP modi
* Bugfixes
- bug #40055: AVRDUDE segfaults when writing eeprom
- bug #40085: Typo fix in fuses report (for 6.1-svn-20130917)
- bug #40782: Verify errors for object size > 16 k on x32e5 due
to typo in avrdude.conf
- bug #40817: Elf file support (possibly) not working on 6.0.1 windows build
- bug #40897: AT Mega2560 not correctly programmed with stk500(v1)
ISP (solution patch)
- bug #41357: OS X: Avrdude messes with the usb stack?
- bug #41402: dfu.c missing include <stdint.h>
- patch #7896: DFU FLIPv2 programming support
- patch #XXXX: xxx
* Internals:
- (Some) programmers can take a list of USB PIDs now.
|
|
- Bump version 5.11 to 6.0.1
(See cvs log for Makefile for changes).
(pkgsrc)
- Add patches/patch-fileio_c to avoid following problem:
fileio.c:957:3: warning: implicit declaration of function 'elf_getshdrstrndx'
|
|
----------------------------------------------------------------------
Version 6.0.1:
* Major changes compared to the previous version:
- Programmer types in configuration file are no longer keywords but
specified as string.
So you need to change 'type = XYZ;' to 'type = "XYZ";' in own
config files. (internal: The parser does not need to know all
programmer types now, new programmers will update only the table
in pgm_type.c.)
- The erase cycle counter (formerly options -y / -Y) has been
removed.
- Specifying a -U option without a memory type (short form of
option argument list) now defaults to "application" memory for
Xmega devices, and "flash" for everything else. This ensures
the Xmega bootloader is not accidentally touched.
- For programmers that support it, the default erase method is a
page erase now, rather than a chip erase (Xmega only).
- Keep track of input file contents
Memory segments are being tracked to remember whether they've
been actually read from a file. Only segments that came from a
file are being programmed into the device, or considered for
verification. This drastically improves handling speed for
sparse files (e.g. files that have a second bootloader segment),
and it ensures the device contents is actually compared for
everything mentioned in the file (even in case the file has
large 0xFF blocks).
- The -U option now accepts ELF files as input files, and extracts
the appropriate section contents that matches the requested memory
region. To enable this feature, the host system used for the
compilation must have a libelf around, including the respective
header files (i.e., package "libelf-devel" on many Linux systems).
- Programmers and parts lists
They are now sorted at output with '-c ?'/'-p ?'. (patch #7671:
Sorting programmers and parts lists for console output)
Programmers and parts lists in documentation generated from lists
mentioned above. (patch #7687: Autogenerating programmers and
parts lists for docs)
Output list of programmer types with '-c ?type', add list to
documentation
- Configuration files now accepts parent parts/programmers, parts
starting with '.' (eg. .xmega) are not included in output parts
list and can be used as abstract parents
(bug #34302: Feature request : device configuration with parent classes)
(patch #7688: Implement parent programmers feature)
- Additional config files which are read after default can be
specified on command line using '-C +filename'
(patch #7699 Read additional config files)
- "Safemode" can now be turned off by default from within a
configuration file (like ~/.avrduderc).
- The new option -l logfile allows to redirect diagnostic messages
to a logfile rather than stderr. Useful to record debugging
traces, in particular in environments which do not offer
shell-style redirection functionality for standard streams.
- When leaving debugWIRE mode, immediately retry with ISP rather
than bailing out completely.
- The USBasp programmer implementation now supports detailed traces
with -vvv, and device communication traces with -vvvv.
- The "verbose" terminal mode command allows to query or modify the
verbosity level.
* New devices supported:
- ATmega48P (patch #7629 add support for atmega48p)
- AT90PWM316 (bug #21797: AT90PWM316: New part description)
- ATxmega16D4, ATxmega32D4, ATxmega64D4, ATxmega128D4
- ATmega256RFR2, ATmega128RFR2, ATmega64RFR2, ATmega2564RFR2,
ATmega1284RFR2, ATmega644RFR2
- ATtiny1634
- ATxmega128A1U, ATxmega128A3U, ATxmega128A4U, ATxmega128B1,
ATxmega128B3, ATxmega128C3, ATxmega128D3, ATxmega16A4U,
ATxmega16C4, ATxmega192A3U, ATxmega192C3, ATxmega192D3,
ATxmega256A3BU, ATxmega256A3U, ATxmega256C3, ATxmega256D3,
ATxmega32A4U, ATxmega32C4, ATxmega384C3, ATxmega384D3,
ATxmega64A1U, ATxmega64A3U, ATxmega64A4U, ATxmega64B1,
ATxmega64B3, ATxmega64C3, ATxmega64D3
- ATtiny43U
- ATmega406
- ATxmega8E5, ATxmega16E5, ATxmega32E5
- ATtiny20, ATtiny40
* New programmers supported:
- linuxgpio
+ any (embedded) Linux system with 4 GPIOs available can be used
as a programmer with little or no additional hardware.
- avrftdi
+ o-link (patch #7672 adding support for O-Link (FTDI based
JTAG) as programmer)
+ 4232h (patch #7715 FT4232H support)
- TPI support
+ openmoko (bug #37977 Support for Openmoko Debug Board)
- usbasp
+ nibobee (previously specified as '-c usbasp -P nibobee)
+ usbasp-clone (same as usbasp but ignores vendor and product
string, checks only vid/pid)
- ftdi_syncbb (new type for synchronous bitbanging with ft232r/ft245r)
+ ft245r (FT245R Synchronous BitBang, miso = D1, sck = D0, mosi
= D2, reset = D4)
+ ft232r (FT232R Synchronous BitBang, miso = RxD, sck = RTS,
mosi = TxD, reset = DTR)
+ bwmega (BitWizard ftdi_atmega builtin programmer, miso = DSR,
sck = DCD, mosi = CTS, reset = RI)
+ arduino-ft232r (Arduino: FT232R connected to ISP, miso = CTS
X3(1), sck = DSR X3(2), mosi = DCD X3(3), reset = RI X3(4))
+ diecimila (alias for arduino-ft232r)
- pickit2
- Atmel JTAGICE3
- buspirate_bb (TPI programming using the BusPirate in bitbang mode)
* Bugfixes
- bug #34027: avrdude AT90S1200 Problem
- bug #34518: loading intel hex files > 64k using record-type 4
- patch #7667: Minor memory handling fixes
- patch #7680: Fixing timeout problem in ser_recv in ser_win32.c
- patch #7693: Fix config file atmel URLs (+ URLs in
avrdude.texi and avrpart.h)
- bug #21663: AT90PWM efuse incorrect, bug #30438: efuse bits
written as 0 on at90pwmxx parts
- bug #35261: avrftdi uses wrong interface in avrftdi_paged_(write|load)
- patch #7437 modifications to Bus Pirate module
- patch #7686 Updating buspirate ascii mode to current firmware,
use AUX as clock generator, and setting of serial receive
timeout
- bug #34768 Proposition: Change the name of the AVR32 devices
- patch #7718: Merge global data of avrftdi in a private data
structure
- bug #35208: avrdude 5.11 on freebsd 8.2-STABLE does not reset
Arduino Uno properly
- bug #34518: loading intel hex files > 64k using record-type 4
(Extended Linear Address Record)
- bug #34027: avrdude AT90S1200 Problem
- bug #30451: Accessing some Xmega memory sections gives not
supported error
- bug #28744: Can't load bootloader to xmega128a1
- bug #29019: pagel/bs2 warning when uploading using stk500 to xmega
- bug #30756: When setting SUT to 64ms on XMEGA, avrdude doesn't
read device signature
- bug #37265: wrong page sizes for XMega64xx in avrdude.conf
- bug #37942: Latest SVN can't program in dragon_jtag mode
- patch #7876 JTAGICE mkII fails to connect to attiny if debugwire
is enabled AND target has a very slow clock
- bug #39893: Verification failure with AVRISPmkII and Xmega
- bug #38713: Compilation of the documentation breaks with texinfo-5
- bug #38023: avrdude doesn't return an error code when attempting
to upload an invalid Intel HEX file
- bug #39794: warnings when building avrdude 6.0rc1 under CentOS 6.4
- bug #35800: Compilation error on certain systems if parport is disabled
- bug #38307: Can't write usersig of an xmega256a3
- bug #38580: Current svn head, xmega and fuses, all fuses tied to fuse0
- bug #39691: Buffer overrun when reading EEPROM byte with JTAGICE3
- bug #38951: AVR109 use byte offset instead of word offset
- patch #7769: Write flash fails for AVR910 programmers
- bug #38732: Support for ATtiny1634
- bug #36901: flashing Atmega32U4 EEPROM produces garbage on chip
- bug #28344: chip_erase_delay too short for ATmega324P, 644, 644P, and 1284P
- bug #34277: avrdude reads wrong byte order if using avr911 (aka butterfly)
- bug #35456: The progress bar for STK500V2 programmer is "wrong".
- patch #5708: avrdude should make 10 synchronization attempts instead of just one
- patch #7606: ATtiny43u support
- patch #7657: Add ATmega406 support for avrdude using DRAGON + JTAG
- bug #35474: Feature request: print fuse values in safemode output.
- patch #7710: usb_libusb: Check VID/PID before opening device
- [no-id]: Fix SCK period adjustment for STK500v2
- bug #40040: Support for ATtiny20 and ATtiny40
- bug #40055: AVRDUDE segfaults when writing eeprom
|
|
entry, as the permissions are not exotic.
|
|
are replaced with .include "../../devel/readline/buildlink3.mk", and
USE_GNU_READLINE are removed,
* .include "../../devel/readline/buildlink3.mk" without USE_GNU_READLINE
are replaced with .include "../../mk/readline.buildlink3.mk".
|
|
|
|
|
|
|
|
(1) update 5.10 to 5.11
(2) Trying to remove pkglint -Wall warning
(3) Update HOMEPAGE URL
----- ----- -----
AVRDUDE 5.11 relesed
(2011/8/27 By joerg_wunsch)
Finally, more than 1.5 years after the previous release,
AVRDUDE 5.11 is finally done. This is mostly a bugfix
release, but also includes a few enhancements. The two
most important enhancements are:
- TPI (i.e. ATtiny4/5/9/10) programming support for bitbang
programmers.
- FTDI MPSSE (FT2232 etc.) bitbang support.
----- ----- -----
|
|
|
|
|
|
|
|
pkgsrc changes:
Rework AVRISP mkII stall workaround.
summary of upstream changes since 5.8:
- Fix problem with loading intel hex rom files that exceed 0x10000 bytes.
- Fix FreeBSD default serial port name.
- jtagmkII.c: If entering JTAG mode fails with a bad JTAG ID message,
retry with external reset applied (in case the target is in sleep
mode or has asserted the JTD bit).
- Fix build for GNU/kFreeBSD.
|
|
is really a oddity of NetBSD's USB stack, but this seems to work too.
Also, hello nb2 and set LICENSE.
(This commit bumps most of the patch files only because of
pkgdiff timestamp formatting differences. Sigh.)
|
|
Thereby hitherto forth yonder the revision is bumped.
|
|
|
|
here. All hard update work done by Simon 'corecode' Schubert and minor
modifications by me.
|
|
|
|
major change.
Reported by Robert Elz in PR 41345.
|
|
|
|
|
|
|
|
pkgsrc-users.
|
|
autoconf tests, fixed a non portable call to the shell builtin
test, and use the pkgsrc DEFAULT_SERIAL_DEVICE variable for setting
the serial device.
|
|
Significant enhancements in this version are:
o Support for JTAGICE MkII device
o New devices supported:
- AT90CAN128 ...
o Support for STK500 Version 2 Protocol
(the latter being the principal reason for the update, as the recent
firmware on the STK500 development boards requires protocol version 2)
|
|
shortly.
|
|
Mailbox closed for this recipient
|
|
|
|
modern etex by forcing it to output pdf instead of dvi.
* List the info files directly in the PLIST.
|
|
makeinfo if no native makeinfo executable exists. Honor TEXINFO_REQD
when determining whether the native makeinfo can be used.
* Remove USE_MAKEINFO and replace it with USE_TOOLS+=makeinfo.
* Get rid of all the "split" argument deduction for makeinfo since
the PLIST module already handles varying numbers of split info files
correctly.
NOTE: Platforms that have "makeinfo" in the base system should check
that the makeinfo entries of pkgsrc/mk/tools.${OPSYS}.mk are
correct.
|
|
|
|
example MAKE_ENV+=FOO=${BAR} is changed to MAKE_ENV+=FOO=${BAR:Q}. Some
other changes are outlined in
http://mail-index.netbsd.org/tech-pkg/2005/12/02/0034.html
|
|
It is more consistent with the tex.buildlink3.mk name. Also, if a package
really needs latex, it just has to set TEX_ACCEPTED to latex distributions
altough today, all TEX_ACCEPTED possibilities are latex distributions
|
|
use BUILD_DEPMETHOD=build
|
|
|
|
and depend on latest version, since it causes PLIST changes. Adapt PLIST.
Bump PKGREVISION.
|
|
|
|
|
|
Buildlink files: RECOMMENDED version changed to current version.
|
|
|
|
|
|
Handle info files properly.
|
|
|
|
Submitted by Karl Janmar <karlj@mdstud.chalmers.se> in PR 22139,
with several changes by myself. Original package from FreeBSD.
|
