diff options
Diffstat (limited to 'doc/codereview_with_mq.html')
-rw-r--r-- | doc/codereview_with_mq.html | 113 |
1 files changed, 113 insertions, 0 deletions
diff --git a/doc/codereview_with_mq.html b/doc/codereview_with_mq.html new file mode 100644 index 000000000..33f415f13 --- /dev/null +++ b/doc/codereview_with_mq.html @@ -0,0 +1,113 @@ +<!-- Using Mercurial Queues with Codereview --> + +<h2 id="Introduction">Introduction</h2> + +<p> +The Mercurial Queues extension (<code>mq</code>) provides a mechanism for +managing patches on top of a Mercurial repository and is described in detail +in Chapters +<a href="http://hgbook.red-bean.com/read/managing-change-with-mercurial-queues.html">12</a> +and <a href="http://hgbook.red-bean.com/read/advanced-uses-of-mercurial-queues.html">13</a> +of <a href="http://hgbook.red-bean.com/read/">Mercurial: The Definitive Guide</a>. +This document explains how to use <code>mq</code> in conjunction +with the <code>codereview</code> Mercurial extension described in the +instructions for <a href="contribute.html">contributing to the Go project</a>. +It assumes you have read those instructions. +</p> + +<h2>Configuration</h2> + +<p> +To enable <code>mq</code> edit either <code>$HOME/.hgrc</code> (to enable it +for all of your repositories) or <code>$GOROOT/.hg/hgrc</code> (to enable it for the +repository at <code>$GOROOT</code>) to add:</p> + +<pre> +[extensions] +mq= +</pre> + +<p> +Since pulling, pushing, updating and committing while <code>mq</code> patches +are applied can damage your repository or a remote one, add these lines to +prevent that case: +</p> + +<pre> +[hooks] +# Prevent "hg pull" if MQ patches are applied. +prechangegroup.mq-no-pull = ! hg qtop > /dev/null 2>&1 +# Prevent "hg push" if MQ patches are applied. +preoutgoing.mq-no-push = ! hg qtop > /dev/null 2>&1 +# Prevent "hg update" if MQ patches are applied. +preupdate.mq-no-update = ! hg qtop > /dev/null 2>&1 +</pre> + +<h2>Making a change</h2> + +<p> +The entire checked-out tree is writable and you can use <code>mq</code>, +as documented in Chapter +<a href="http://hgbook.red-bean.com/read/managing-change-with-mercurial-queues.html">12</a> +of "The Guide", +to implement your change as a single patch or a series of patches. + +</p> + +<p>When you are ready to send a change out for review, run</p> + +<pre> +$ hg change +</pre> + +<p>from any directory in your Go repository with all of the <code>mq</code> patches relevant to your +change applied and then proceed as instructed in <a href="contribute.html">contributing +to the Go project</a>. +</p> + +<p> +The change number reported by <code>hg change</code>, preceded by a <code>+</code>, +can be used as an <code>mq</code> patch guard to assist in controlling which patches +are applied as described in Chapter +<a href="http://hgbook.red-bean.com/read/advanced-uses-of-mercurial-queues.html">13</a> +of "The Guide". +For example, the command: +</p> + +<pre> +for p in $(hg qapplied); do hg qguard $p +99999; done +</pre> + +<p> +will apply the guard <code>+99999</code> guard to all currently applied <code>mq</code> +patches. +</p> + +<h2>Synchronizing your client</h2> + +<p>While you were working, others might have submitted changes +to the repository and, as explained in <a href="contribute.html">contributing +to the Go project</a>, it is necessary to synchronize your repository using +<code>hg sync</code>before sending your change list for review. +Because <code>hg sync</code> runs <code>hg pull -u</code>, +you should not run <code>hg sync</code> while <code>mq</code> patches are +applied. Instead +pop all your patches before running <code>hg sync</code> and reapply them after +it has completed. +</p> + +<p> +When reapplying the patches, you may need to resolve conflicts +as described in <a href="contribute.html">contributing to the Go project</a>. +</p> + +<h2>Mailing the change for review</h2> + +<p> +You should have all of the <code>mq</code> patches relevant to your +change applied when you run <code>hg mail</code>. + +<h2>Submitting the change after the review</h2> + +If you are a committer, you should have all of the <code>mq</code> patches relevant to your +change applied when you run <code>hg commit</code>. |