1 files changed, 19 insertions, 6 deletions
diff --git a/doc/install-source.html b/doc/install-source.html
index b99360c71..6f6a15afd 100644
--- a/doc/install-source.html
+++ b/doc/install-source.html
@@ -69,8 +69,8 @@ goroutines, such as stacks that grow and shrink on demand.
 </p>
 
 <p>
-The compilers can target the FreeBSD, Linux, NetBSD, OpenBSD, OS X (Darwin), Plan 9,
-and Windows operating systems.
+The compilers can target the DragonFly BSD, FreeBSD, Linux, NetBSD, OpenBSD,
+OS X (Darwin), Plan 9, Solaris and Windows operating systems.
 The full set of supported combinations is listed in the discussion of
 <a href="#environment">environment variables</a> below.
 </p>
@@ -95,7 +95,7 @@ have an <code>hg</code> command.)
 <p>
 If you do not have a working Mercurial installation,
 follow the instructions on the
-<a href="http://mercurial.selenic.com/downloads/">Mercurial downloads</a> page.
+<a href="http://mercurial.selenic.com/downloads">Mercurial downloads</a> page.
 </p>
 
 <p>
@@ -176,6 +176,10 @@ architecture, and root directory used during the install.
 <p>
 For more information about ways to control the build, see the discussion of
 <a href="#environment">environment variables</a> below.
+<code>all.bash</code> (or <code>all.bat</code>) runs important tests for Go,
+which can take more time than simply building Go. If you do not want to run
+the test suite use <code>make.bash</code> (or <code>make.bat</code>)
+instead.
 </p>
 </div>
 
@@ -354,9 +358,9 @@ These default to the values of <code>$GOHOSTOS</code> and
 
 <p>
 Choices for <code>$GOOS</code> are
-<code>darwin</code> (Mac OS X 10.6 and above), <code>freebsd</code>,
+<code>darwin</code> (Mac OS X 10.6 and above), <code>dragonfly</code>, <code>freebsd</code>,
 <code>linux</code>, <code>netbsd</code>, <code>openbsd</code>, 
-<code>plan9</code>, and <code>windows</code>.
+<code>plan9</code>, <code>solaris</code> and <code>windows</code>.
 Choices for <code>$GOARCH</code> are
 <code>amd64</code> (64-bit x86, the most mature port),
 <code>386</code> (32-bit x86), and <code>arm</code> (32-bit ARM).
@@ -372,6 +376,12 @@ The valid combinations of <code>$GOOS</code> and <code>$GOARCH</code> are:
 <td></td><td><code>darwin</code></td> <td><code>amd64</code></td>
 </tr>
 <tr>
+<td></td><td><code>dragonfly</code></td> <td><code>386</code></td>
+</tr>
+<tr>
+<td></td><td><code>dragonfly</code></td> <td><code>amd64</code></td>
+</tr>
+<tr>
 <td></td><td><code>freebsd</code></td> <td><code>386</code></td>
 </tr>
 <tr>
@@ -411,6 +421,9 @@ The valid combinations of <code>$GOOS</code> and <code>$GOARCH</code> are:
 <td></td><td><code>plan9</code></td> <td><code>amd64</code></td>
 </tr>
 <tr>
+<td></td><td><code>solaris</code></td> <td><code>amd64</code></td>
+</tr>
+<tr>
 <td></td><td><code>windows</code></td> <td><code>386</code></td>
 </tr>
 <tr>
@@ -444,7 +457,7 @@ installs all commands there.
 </p>
 
 <li><code>$GO386</code> (for <code>386</code> only, default is auto-detected
-if built natively, <code>387</code> if not)
+if built on either <code>386</code> or <code>amd64</code>, <code>387</code> otherwise)
 <p>
 This controls the code generated by 8g to use either the 387 floating-point unit
 (set to <code>387</code>) or SSE2 instructions (set to <code>sse2</code>) for