UDP Syslog Input Module

Module Name: imudp

Author: Rainer Gerhards <rgerhards@adiscon.com>

Multi-Ruleset Support: since 5.3.2

Description:

Provides the ability to receive syslog messages via UDP.

Multiple receivers may be configured by specifying multiple input actions.

Configuration Parameters:

Module Parameters:

TimeRequery <nbr-of-times>
this is a performance optimization. Getting the system time is very costly. With this setting, imudp can be instructed to obtain the precise time only once every n-times. This logic is only activated if messages come in at a very fast rate, so doing less frequent time calls should usually be acceptable. The default value is two, because we have seen that even without optimization the kernel often returns twice the identical time. You can set this value as high as you like, but do so at your own risk. The higher the value, the less precise the timestamp.
SchedulingPolicy <rr/fifo/other>
Can be used the set the scheduler priority, if the necessary functionality is provided by the platform. Most useful to select "fifo" for real-time processing under Linux (and thus reduce chance of packet loss).
SchedulingPriority <number>
Scheduling priority to use.

Input Parameters:

Address <IP>
local IP address (or name) the UDP listens should bind to
Port <port>
default 514, start UDP server on this port. Either a single port can be specified or an array of ports. If multiple ports are specified, a listener will be automatically started for each port. Thus, no additional inputs need to be configured.
Single port: Port="514"
Array of ports: Port=["514","515","10514","..."]
Ruleset <ruleset>
Binds the listener to a specific ruleset.
RateLimit.Interval [number] - (available since 7.3.1) specifies the rate-limiting interval in seconds. Default value is 0, which turns off rate limiting. Set it to a number of seconds (5 recommended) to activate rate-limiting.
RateLimit.Burst [number] - (available since 7.3.1) specifies the rate-limiting burst in number of messages. Default is 10,000.
InputName [name] - (available since 7.3.9) specifies the value of the inputname. In older versions, this was always "imudp" for all listeners, which still i the default. Starting with 7.3.9 it can be set to different values for each listener. Note that when a single input statement defines multipe listner ports, the inputname will be the same for all of them. If you want to differentiate in that case, use "InputName.AppendPort" to make them unique. Note that the "InputName" parameter can be an empty string. In that case, the corresponding inputname property will obviously also be the empty string. This is primarily meant to be used togehter with "InputName.AppendPort" to set the inputname equal to the port.
InputName.AppendPort [on/off] - (available since 7.3.9) appends the port the the inputname. Note that when no inputname is specified, the default of "imudp" is used and the port is appended to that default. So, for example, a listner port of 514 in that case will lead to an inputname of "imudp514". The ability to append a port is most useful when multiple ports are defined for a single input and each of the inputnames shall be unique. Note that there currently is no differentiation between IPv4/v6 listeners on the same port.

Caveats/Known Bugs:

Scheduling parameters are set after privileges have been dropped. In most cases, this means that setting them will not be possible after privilege drop. This may be worked around by using a sufficiently-privileged user account.

Samples:

This sets up an UPD server on port 514:

In the next example, we set up three listeners at ports 10514, 10515 and 10516 and assign a listner name of "udp" to it, followed by the port number:

The next example is almost equal to the previous one, but now the inputname property will just be set to the port number. So if a message was received on port 10515, the input name will be "10515" in this example whereas it was "udp10515" in the previous one. Note that to do that we set the inputname to the empty string.

Legacy Configuration Directives:

Multiple receivers may be configured by specifying $UDPServerRun multiple times.

$UDPServerAddress <IP>
equivalent to: Address
$UDPServerRun <port>
equivalent to: Port
$UDPServerTimeRequery <nbr-of-times>
equivalent to: TimeRequery
$InputUDPServerBindRuleset <ruleset>
equivalent to: Ruleset
$IMUDPSchedulingPolicy <rr/fifo/other> Available since 4.7.4+, 5.7.3+, 6.1.3+.
equivalent to: SchedulingPolicy
$IMUDPSchedulingPriority <number> Available since 4.7.4+, 5.7.3+, 6.1.3+.
equivalent to: SchedulingPriority

Sample:

This sets up an UPD server on port 514:

[rsyslog.conf overview] [manual index] [rsyslog site]