path: root/usr/src/uts/common/io/rtw/sa2400reg.h

/*
 * Copyright 2009 Sun Microsystems, Inc.  All rights reserved.
 * Use is subject to license terms.
 */
/*
 * Copyright (c) 2005 David Young.  All rights reserved.
 *
 * This code was written by David Young.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the author nor the names of any co-contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY David Young ``AS IS'' AND ANY
 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
 * PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL David
 * Young BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
 * OF SUCH DAMAGE.
 */
#ifndef _SA2400REG_H_
#define	_SA2400REG_H_

#ifdef __cplusplus
extern "C" {
#endif

/*
 * Serial bus format for Philips SA2400 Single-chip Transceiver.
 */
#define	SA2400_TWI_DATA_MASK	BITS(31, 8)
#define	SA2400_TWI_WREN		BIT(7)		/* enable write */
#define	SA2400_TWI_ADDR_MASK	BITS(6, 0)

/*
 * Registers for Philips SA2400 Single-chip Transceiver.
 */
#define	SA2400_SYNA		0		/* Synthesizer Register A */
/*
 * fractional modulus select,
 * 0: /8 (default)
 * 1: /5
 */
#define	SA2400_SYNA_FM		BIT(21)
/*
 * fractional increment value,
 * 0 to 7, default 4
 */
#define	SA2400_SYNA_NF_MASK	BITS(20, 18)
/*
 * main divider division ratio,
 * 512 to 65535, default 615
 */
#define	SA2400_SYNA_N_MASK	BITS(17, 2)

#define	SA2400_SYNB		1		/* Synthesizer Register B */
/*
 * reference divider ratio,
 * 4 to 1023, default 11
 */

#define	SA2400_SYNB_R_MASK	BITS(21, 12)
#define	SA2400_SYNB_L_MASK	BITS(11, 10)	/* lock detect mode */
#define	SA2400_SYNB_L_INACTIVE0	LSHIFT(0, SA2400_SYNB_L_MASK)
#define	SA2400_SYNB_L_INACTIVE1	LSHIFT(1, SA2400_SYNB_L_MASK)
#define	SA2400_SYNB_L_NORMAL	LSHIFT(2, SA2400_SYNB_L_MASK)
#define	SA2400_SYNB_L_INACTIVE2	LSHIFT(3, SA2400_SYNB_L_MASK)

/*
 * power on/off,
 * 0: inverted chip mode control
 * 1: as defined by chip mode (see SA2400_OPMODE)
 */

#define	SA2400_SYNB_ON		BIT(9)
#define	SA2400_SYNB_ONE		BIT(8)		/* always 1 */
/*
 * fractional compensation
 * charge pump current DAC,
 * 0 to 255, default 80.
 */

#define	SA2400_SYNB_FC_MASK	BITS(7, 0)
#define	SA2400_SYNC		2		/* Synthesizer Register C */
#define	SA2400_SYNC_CP_MASK	BITS(7, 6) /* charge pump current setting */
#define	SA2400_SYNC_CP_NORMAL_	LSHIFT(0, SA2400_SYNC_CP_MASK)
#define	SA2400_SYNC_CP_THIRD_	LSHIFT(1, SA2400_SYNC_CP_MASK)
#define	SA2400_SYNC_CP_NORMAL	LSHIFT(2, SA2400_SYNC_CP_MASK) /* recommended */
#define	SA2400_SYNC_CP_THIRD	LSHIFT(3, SA2400_SYNC_CP_MASK)

/*
 * comparison divider select,
 * 0 to 4, extra division
 * ratio is 2**SM.
 */
#define	SA2400_SYNC_SM_MASK	BITS(5, 3)
#define	SA2400_SYNC_ZERO	BIT(2)		/* always 0 */

#define	SA2400_SYND		3		/* Synthesizer Register D */
#define	SA2400_SYND_ZERO1_MASK	BITS(21, 17)	/* always 0 */
/*
 * T[phpsu], 1: disable
 * PHP speedup pump,
 * overrides SA2400_SYND_TSPU
 */
#define	SA2400_SYND_TPHPSU	BIT(16)
/*
 * T[spu], 1: speedup on,
 * 0: speedup off
 */
#define	SA2400_SYND_TPSU	BIT(15)
#define	SA2400_SYND_ZERO2_MASK	BITS(14, 3)	/* always 0 */
/*
 * Operating mode, filter tuner,
 * other controls
 */
#define	SA2400_OPMODE		4
/*
 * 1: in Rx mode, RSSI-ADC always on
 * 0: RSSI-ADC only on during AGC
 */
#define	SA2400_OPMODE_ADC	BIT(19)
/*
 * read-only filter tuner error:
 * 1 if tuner out of range
 */
#define	SA2400_OPMODE_FTERR	BIT(18)
/*
 * Rx & Tx filter tuning, write tuning value (test mode only) or
 * read tuner setting (in normal mode).
 */
#define	SA2400_OPMODE_FILTTUNE_MASK	BITS(17, 15)
/*
 * external reference voltage
 * (pad v2p5) on
 */
#define	SA2400_OPMODE_V2P5	BIT(14)
#define	SA2400_OPMODE_I1M	BIT(13)	/* external reference current ... */
#define	SA2400_OPMODE_I0P3	BIT(12)	/* external reference current ... */
/*
 * xtal input frequency,
 * 0: 44 MHz
 * 1: 22 MHz
 */
#define	SA2400_OPMODE_IN22	BIT(10)
#define	SA2400_OPMODE_CLK	BIT(9)	/* reference clock output on */
#define	SA2400_OPMODE_XO	BIT(8)	/* xtal oscillator on */
#define	SA2400_OPMODE_DIGIN	BIT(7)	/* use digital Tx inputs (FIRDAC) */
/*
 * Rx output common mode voltage,
 * 0: V[DD]/2
 * 1: 1.25V
 */
#define	SA2400_OPMODE_RXLV	BIT(6)
/*
 * make internal vco
 * available at vco pads (vcoextout)
 */
#define	SA2400_OPMODE_VEO	BIT(5)
#define	SA2400_OPMODE_VEI	BIT(4)	/* use external vco input (vcoextin) */
/* main operating mode */
#define	SA2400_OPMODE_MODE_MASK		BITS(3, 0)
#define	SA2400_OPMODE_MODE_SLEEP	LSHIFT(0, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_TXRX		LSHIFT(1, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_WAIT		LSHIFT(2, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_RXMGC	LSHIFT(3, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_FCALIB	LSHIFT(4, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_DCALIB	LSHIFT(5, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_FASTTXRXMGC	LSHIFT(6, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_RESET	LSHIFT(7, SA2400_OPMODE_MODE_MASK)
#define	SA2400_OPMODE_MODE_VCOCALIB	LSHIFT(8, SA2400_OPMODE_MODE_MASK)

#define	SA2400_OPMODE_DEFAULTS						\
	(SA2400_OPMODE_XO | SA2400_OPMODE_RXLV | SA2400_OPMODE_CLK |	\
	SA2400_OPMODE_I0P3 | LSHIFT(3, SA2400_OPMODE_FILTTUNE_MASK))

#define	SA2400_AGC		5		/* AGC adjustment */
/*
 * fine-tune AGC target:
 * -7dB to 7dB, sign bit ...
 */
#define	SA2400_AGC_TARGETSIGN	BIT(23)
#define	SA2400_AGC_TARGET_MASK	BITS(22, 20)	/* ... plus 0dB - 7dB */
/*
 * maximum AGC gain, 0 to 31, (yields 54dB to 85dB)
 */
#define	SA2400_AGC_MAXGAIN_MASK	BITS(19, 15)
/*
 * write: settling time after baseband gain switching, units of
 *        182 nanoseconds.
 * read:  output of RSSI/Tx-peak detector's ADC in 5-bit Gray code.
 */
#define	SA2400_AGC_BBPDELAY_MASK	BITS(14, 10)
#define	SA2400_AGC_ADCVAL_MASK		SA2400_AGC_BBPDELAY_MASK

/*
 * write: settling time after LNA gain switching, units of
 *        182 nanoseconds
 * read:  2nd sample of RSSI in AGC cycle
 */
#define	SA2400_AGC_LNADELAY_MASK	BITS(9, 5)
#define	SA2400_AGC_SAMPLE2_MASK		SA2400_AGC_LNADELAY_MASK

/*
 * write: time between turning on Rx and AGCSET, units of
 *        182 nanoseconds
 * read:  1st sample of RSSI in AGC cycle
 */
#define	SA2400_AGC_RXONDELAY_MASK	BITS(4, 0)
#define	SA2400_AGC_SAMPLE1_MASK		SA2400_AGC_RXONDELAY_MASK

#define	SA2400_MANRX		6	/* Manual receiver control settings */
/*
 * 1: AGC w/ high S/N---switch LNA at
 *    step 52 (recommended)
 * 0: switch LNA at step 60
 */
#define	SA2400_MANRX_AHSN	BIT(23)

/*
 * If _RXOSQON, Q offset is
 * (_RXOSQSIGN ? -1 : 1) * (1 + _RXOSQ_MASK) * 8 millivolts,
 * otherwise, Q offset is 0.
 *
 * Ditto I offset.
 */
#define	SA2400_MANRX_RXOSQON	BIT(22)		/* Rx Q-channel correction. */
#define	SA2400_MANRX_RXOSQSIGN	BIT(21)
#define	SA2400_MANRX_RXOSQ_MASK	BITS(20, 18)

#define	SA2400_MANRX_RXOSION	BIT(17)		/* Rx I-channel correction. */
#define	SA2400_MANRX_RXOSISIGN	BIT(16)
#define	SA2400_MANRX_RXOSI_MASK	BITS(15, 13)
/*
 * use 10MHz offset cancellation cornerpoint for brief period
 * after each gain change
 */
#define	SA2400_MANRX_TEN	BIT(12)

/*
 * DC offset cancellation cornerpoint select
 * write: in RXMGC, set the cornerpoint
 * read:  in other modes, read AGC-controlled cornerpoint
 */
#define	SA2400_MANRX_CORNERFREQ_MASK	BITS(11, 10)

/*
 * write: in RXMGC mode, sets receiver gain
 * read:  in other modes, read AGC-controlled gain
 */
#define	SA2400_MANRX_RXGAIN_MASK	BITS(9, 0)

#define	SA2400_TX	7		/* Transmitter settings */
/*
 * Tx offsets
 * write: in test mode, sets the offsets
 * read:  in normal mode, returns automatic settings
 */
#define	SA2400_TX_TXOSQON	BIT(19)
#define	SA2400_TX_TXOSQSIGN	BIT(18)
#define	SA2400_TX_TXOSQ_MASK	BITS(17, 15)
#define	SA2400_TX_TXOSION	BIT(14)
#define	SA2400_TX_TXOSISIGN	BIT(13)
#define	SA2400_TX_TXOSI_MASK	BITS(12, 10)

/*
 * Ramp-up delay,
 * 0: 1us
 * 1: 2us
 * 2: 3us
 * 3: 4us
 * datasheet says, "ramp-up
 * time always 1us". huh?
 */
#define	SA2400_TX_RAMP_MASK	BITS(9, 8)
/*
 * Transmitter gain settings
 * for TXHI output
 */
#define	SA2400_TX_HIGAIN_MASK	BITS(7, 4)
/*
 * Transmitter gain settings
 * for TXLO output
 */
#define	SA2400_TX_LOGAIN_MASK	BITS(3, 0)

#define	SA2400_VCO	8			/* VCO settings */
#define	SA2400_VCO_ZERO		BITS(6, 5)	/* always zero */
/*
 * VCO calibration error flag---no
 * band with low enough frequency
 * could be found
 */
#define	SA2400_VCO_VCERR	BIT(4)
/*
 * VCO band,
 * write: in test mode, sets
 *        VCO band
 * read:  in normal mode,
 *        the result of
 *        calibration (VCOCAL).
 *        0 = highest
 *        frequencies
 */
#define	SA2400_VCO_VCOBAND_MASK	BITS(3, 0)
#ifdef __cplusplus
}
#endif

#endif /* _SA2400REG_H_ */